Description
AVURE (ASEA) QUINTUS FLUID CELL FORMING PRESS
Model QRF-40, Deep Draw Cavity Die Forming Press
Serial Number L0159.1053-1
SPECIFICATIONS:
CAPACITY 38 MN
FLUID FORM UNIT: Ø = 800 mm
BLANK DIAMETER, (DIE)
Nominal diameter 30.63" (778 mm)
Outer diameter 44.09448" (1120 mm)
Height (unloaded) 34.80" (884 mm)
Maximum recommended Blank Diameter 29.92" (760 mm)
Maximum Draw Depth 13.976 (355 mm)
Maximum Forming Pressure at 38 MN 10,877.83 psi. (75MPa)
50 MPa = 1,566,407.567 Pounds /Square Foot = Tonnage 7,252 Tons
Total weight 11,905 lbs. (5400 kg) Oil volume 160 1
CYLINDER and RAM
Height (Retracted) 41.73" (1060 mm)
Width 38.98" (990 mm)
Maximum Hydraulic Pressure 7,251.8867 psi (50 MPa)
Maximum Force, Outer Ram 38MN
Stroke, Outer Ram 22.05" (560 mm)
Stroke, Inner Ram 13.976" (355 mm)
CONTROLS:
Located on and with-in MAIN ELECTRICAL OPERATOR CONTROL CABINET:
CRT. Circuit Breaker, Relays, Contactors, Fault Signal System,
Indication Signal Indicators, Annunciator Panels, Cycle Counter and Timers,
Press Command - Function Push Buttons, Pump Motors Start - Stop Buttons,
Press Operation Selector Switches, Emergency Stop Button.
OPERATOR MOBIL PUSH BUTTON CONTROL STATION with:
Dual Hand Cycle Start Push Buttons, Start - Stop Buttons and Emergency Stop Button.
EQUIPPED WITH:
1- Operator Mobil Control Station with Dual hand cycle start push buttons,
Start & Emergency Stop Button.
1- Control Station with Program Keyboard, CRT & Push Button Controls PC.
(2nd) Tool Holder Pod.
1- Pod Manipulator Loader, Pod Storage Misc. 12" thru 30" Tool Rings w/
Storage Rack & Special Rings.
1-Lot Misc. Set up Table with set-up parts. SAFETY ENCLOSURE:
Point of Operation,
Right & Left Side and Rear Enclosure, with Light Curtain.
Operation Manual Mechanical Maintesnance Manuals
Electics Hydraulic & Part & Foundation Drawings
MOTOR DRIVE: Wired 460 volts, 3 phase
Main Hydraulic Pump 197.15 hp (145 kw) 460 volts.
Circulating Pump 7.5 hp. (5.5 kw) 460 volts
Pilot Pump 10.2 hp (7.5 kw) 460 volts
COMPLETE FACTORY SAFETY GUARDS
TYPE OF FORMING: with Cylinder and Ram system.
Cavity die forming.
Male die forming.
Expansion drawing or bulging.
Punch drawing.
Negative punch drawing.
Dimensions: Over-all Height 21′-7" (6,429mm) Total Width 7′-06" (2,150mm),
Total Depth 11′-6" (3,545)
(Total size & weight does not include Safety Enclosure)
Weight Press 127,868.12 lbs. (58,000 kg).
Press Frame: Height retracted 41" (6429 mm).Width 84.7" (2150 mm).
Depth & Daylight width 37.402" (950 mm).
Daylight Column height (length) 22.05" (560 mm).
Net weight 54,572.33 lbs. (24,300 kg.)
Cylinder & Ram Weight 48,281.24 lbs. (21,900 kg.).
Outer Ram weight 6,172.94 lbs. (2,800 kg.).
Inner Ram weight 8,818.49 lbs. (4000 kg.).
Guiding Wheel Holder weight ) 6,613.9 lbs. (3000 kg.)
![8600 tons, Verson Wheelon Fluid Forming Press, Model 8600R-36-92, Forming Pressure 5,000 psi, Forming Depth 4.5" & 6", Serial Number 20995 [P5206-10521]](https://centurymachinery.com/wp-content/uploads/2021/04/10521-1-Verson-Wheelon-8600R-36x92-1-300x300.jpg "8600 Tons Verson Wheelon 8600R-36-92 Fluid Cell Forming Press Forming Pressure 5000 psi two 36 inch x 92 inch Trays Forming Depth 4.5 inch & 6 inch, Serial number 20995, Inventory reference P5206-15923 - Century Machinery")
![60,000 Ton, Verson Wheelon Fluid Cell Forming Press, Model 60000R-50-240, Forming Pressure 10,000 psi, Forming Depth to 10", 2-trays, Depth 6" & 10", Serial Number 21600 [P5206-7106]](https://centurymachinery.com/wp-content/uploads/2021/04/7106-1_verson-wheelon-fluid-forming-press_60000R-50-240_form-press-10K-psi_50-in-x-240-in_depth-10-in_2-trays_Serial-21600-300x300.jpg "60000 Ton Verson Wheelon 60000R-50-240 Fluid Cell Forming Press Forming Pressure 10000 psi Forming Depth 6 inch and 10 inch with-in two trays, Serial Number 21600, Inventory Reference P5206-7106 - Century Machinery")
