Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414]
Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414-6]
Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414-5]
Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414-4]
Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414]
Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees - 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414]

Orton Tilting Spindle Shaper-Router, Model F, Power Tilting 90 degrees – 45 degrees Under & 30 degrees Outward with Readout, Spindle Speeds 10,000 rpm, Drive 5 and10 hp, Vacumm Hold Downs, Serial Number F-93-5140962 [S3053-18414]

Model Number: F

Serial Number: F-93-514962

Reference No: S3034-18414

Condition: Used

Mfg Date:

Model Number F

Serial Number F-93-514962

Reference Number S3034-18414

Read More
1-213-627-2847
Categories: ,

Description

ORTON VERTICAL SHAPER (ROUTER)
  Model  F,  TILTING SPINDLE,   Serial Number F-93-514962
  Condition REBUILT
SPECIFICATIONS
CAPACITY
SPINDLE:
  Tilting: From 90 degrees Vertical, Unit adjustable 45 degrees under to 30 degrees outward.
    Horizontal & Vertical adjustment to bring the top of cutter and the cutting circle to the point 
    of tilt. A vertical height adjustment allows for material thickness. 4" thick material can be cut at full tilt.
  Collet Type: Capacity	 1"
    Taper 11 Brown & Sharpe
    Vertical Adjustment 2½" by Hand Crank
    Power & Hand Tilting of spindle with degree indicator.
SPINDLE SPEED 10,000 rpm
OFFSET GUIDE PIN: Adjust Up & Down, Manually
TABLE SIZE: 40½" LR x 60" FB
MOTOR DRIVES: wired 460 volts, 3 phase
   Spindle 5/10 hp, 220/440 volts
   Power Feed 1/3 hp, 220/440 volts
   Power Tilt 1/3 hp, 220/440 volts
   Vacuum Pump  ¾ hp, 220/440 volts
CONTROLS: Wired 115 volts
   Nema 12 Electrical Combination Control Station
   with: Remote Start/Stop Buttons.   Rapid Stop Button.   Up/Close Buttons.
         Vacuum Pump Start/Stop Buttons.   Tilt Forward/Reverse Buttons.
         Feed Speed Control.   Speed Indicator. 
         Warning Lights: Power On.   Low Lube Oil.   Shear Pin. 
EQUIPPED WITH:
   2-Vacuum Part Holders with Trigger release.
   1- Material Feed System: Variable Feed Geared Drive, w/ Cable winch, fitted with quick- release
       cable drum for fast return.
   1-Power Spindle Tilting.
   1-Overarm Support for Offset Guide.
   1-Spray Mist Bearing Lubricator with Regulator, Low Oil Sensor, Low Voltage Air Valve.
   1-Spindle Foot Brake with Electric Current Shut Off.
   1-D.C. Spindle Motor Brake, Solid State.
   1-Emergency Off foot switch.
PLEASE NOTE: Arbor and Outboard Bearing Support Available at additional cost. 
COMPLETE FACTORY SAFETY GUARDS

Related products...