Scotchman 65T Hydraulic Ironworker Model 6509-24M with Shear 24", Angle Shear 6" x 6", Press Brake, Angle Brake Notcher, Rod Shear, plus much much more, Like New Very Little Use if Any, 10649-1, RIGHT SIDE

Scotchman-65T-Hyd-Ironworker-6509-24M-Open-Ended-Brake-1/4-inch-x-5-inch-with-V-Die-set. 10649-19a

Like New Scotchman 6509-24M Universal 65-T Ironworker with Punch Station – 24″ Shear – Press Brakes 24″ & 12″ – V-Notcher – Rectangular Notcher – Rod Shear 9-Cavity -Tube Shear -Open Ended Brake – Much More Year 2008, Serial Number 7872FF208 , Inventory Reference P8915-10649

Name: Like New Scotchman 6509-24M Universal 65-T Ironworker
Brand: SCOTCHMAN

Like New Scotchman 6509-24M Universal 65-T Ironworker LOADED with ALLMOST ALL OPTIONAL TOOLING Save 45% off New Cost

Model Number: 6509-24M

Serial Number: 7872FF0208

Reference No: LIKE NEW Iron worker, Universal & P8915-10649

Condition: LIKE NEW Very Little Use, IF ANY, almost all Optional Tooling Never Used

Mfg Date:

Model Number 6509-24M

Serial Number 7872FF0208

Reference Number LIKE NEW Iron worker, Universal & P8915-10649

1-213-627-2847 Email Us

Category: IRONWORKERS

Description
Specifications

Description

SCOTCHMAN UNIVERSAL HYDRAULIC IRONWORKER
     Model 6509-24M    Serial Number 78772FF0208   Year Mfg'd 2008

Condition: LIKE NEW Very Little Use, IF ANY, almost all Optional Tooling Never Used

SPECIFICATIONS:
PUNCHING CAPACITY:
Nominal Tonnage 65
    Punch Diameter thru thickness 1-1/16" thru 3/4". 
    with Special Toolingh 4" diameter
    Depth of Throat 9".
    Table 10" X 24" with Scales.
FLAT BAR SHEAR STATION: 24” length Capacity
     1" x 6",   3/4" x 8",   3/16" x 24"
     Saber Blade 1/2" x 16", 3/8" x 24".
     Material Back Gage and Mechanical Sheet Hold-Down
ANGLE SHEAR: "Note Capacity Only"
     Angle at 90 Degrees 6" x 6" x 3/8".   at 45 Degrees 4" x 4" x 1/2"   
PRESS BRAKES (2) both with Fbrication Package
    12" wide x 40 Tons with Table and Back Gauge.
    24" wide x 30 Tons with Table and Back Gauge.
OPEN END BRAKE: 1/4" x 5" [ Flate or Angle Iron ]
ROD SHEAR: 9-Cavity
    Round 1/4" thru 1¼",  Squares 1/4" thru 1" 
SQUARE TUBE SHEAR: 1-Cavity  1/4" thru 2" up to 14 gauge.
V-NOTCHER 90° : 6" x 6" x 5/16".
RECTANGULAR  NOTCHER: 2" x 2" x 3/8".
PIPE NOTCHER: "Note Capacity Only" 40 id 3/4", 1, 1¼", 1½",  2".
MOTOR HYDRAULIC  DRIVE: 5 hp (3.6 kw) 220 volts
CONTROLS:  wired Low Voltage.
    Jog Control,  Adjust electric stroke control, w/ Scale,
    Anti-Repeat Electric Remote Foot Pedal.
EQUIPPED WITH:  "ALMOST ALL TOOLING HAS NEVER BEEN USED"
    1- Shear with 24" W  x 14" D Table & gauge & Rear shoot. 
    1- Square Tube Shear.
    1- Punch Station with. Scale & Gauging.
    2- Stripper Assemblies 3½" & 4" Ht.
    3- Punch Die Holders 2", 2½", 3",Inserts.
    2- Punch Die Nuts.    20- Round Punch & Dies,.  11- Ovels Punch & Dies
            and 4-Square Punch & Dies 
    1- Offset Die Holder with Stripper.
    1- Slug Receptacle.
    1- V-Notcher 90-degree 6" x 6".
    1- Rectangle Notcher.
    1- Rod Shear: 9-Cavity.
    1-Open Ended Brake: 1/4" x 5" [ Flate or Angle Iron ] 
    1- Brake 12" with Table & Back Gauge
    1- Brake 24" with Table & Back Gauge.
    1- lot Press Brake Dies: 15- Miscellaneous Lower V-Dies.  12- Miscellaneous Top Dies.
    1- Press Brake Bed Extension 8¼" X 48" w/ Right hand 20⅜" wide x 24¾" long and
           25-Tool Cut outs Extension & Support.
    1- Heavy duty Split Ring Retaining Nut used in oversize punching applications that require
          a punch with a 2" (51mm) shank diameter.
    1- Die Holder Table 8" x 10"  w/4⅛" dia. Hole.
    1- Punch & Die Holders 2-1/2" and 3" Die Holder Insert (63.5 and 76.2mm).
    1- Punch Die Holder Table 24" FB x 9⅞" LR x 5" Ht w/ Scale.
    1- Punch Die Holder Table 12" LR x 6" FB & Rear shoot x 6"  Ht.
    1- #45 Punch Retaining           1- Work Light.
    1- Wrench 2½" opening.
    Forklift accommodations.
COMPLETE FACTORY SAFETY GUARDS

Dimensions: 60¾" LR x 30" FB x 64½" Ht, (1,543.05 mm LR x 762 FB x 1,638.3 mm Ht.)
    Front to Rear with Right hand Table Extension and tool holder 58"  (1,473.2mm LR).
Weight 2,984 lbs. with Tooling 4,000 lbs.

New cost basic unit $28,211.00 plus Tooling $24,700.00  TOTAL NEW COST  Approximate $52,911.00.
Our price to you at our Los Angeles, CA. warehouse is $28,000.00

USED MACHINERY

WHAT DO YOU HAVE TO SELL?

NEED SOME ASSISTANCE?

Who We Are

Our Warehouse

Export Services

Hotels & Directions