SHRINKERS & STRETCHING MACHINES

Link back to Home Page► www.centurymachinery.com

POINT and CLICK CATEGORIES or JUST SCROLL DOWN, CATEGORIES ARE IN ALPHABETICAL ORDER. ▬▬▬▬▬▬►

*AIRCRAFT GROUND SUPPORT EQUIPMENT*
*ENGLISH WHEEL FORMING MACHINE*
*
SHRINKERS and STRETCHERS  Kick and Pneumatic type
    Mfg. by the following: TCE Erco, Erco, Erco HP Townsend,  Marchant and Eckold*

*STRETCH WRAP FORMING MACHINES, STRETCH PRESS, Mfg'd. by Cyril Bath and
Hufford
SHEET & EXTRUSION STRETCH FORMER, Mfg'd by Sheridan Gray
 *SHEET & EXTRUSION STRETCH FORMER, Mfg'd by Sheridan Gray
 *RADIAL DRAW STRETCH FORMING*   *COMPRESSION FORMING*
 *CONTOUR STRETCH FORMERS*  Mfg'd by Cyril Bath - Sheridan Gray & Hufford
*STRETCH DRAW FORMING PRESS*  Mfg'd by Sheridan Gray

*SWAGGER*

Serving Industry for 83 years


If you require a Quote Sheet PLEASE  send  us your requirements:

CENTURY logo
1937 South Santa Fe Avenue
Los Angeles, California 90021

Email sales@centurymachinery.com
Website  www.centurymachinery.com
Telephone 1-213-627-2847

Fax 1-213-627-2499

"THE WAY A MACHINE LOOKS and THE WAY YOU SEE IT,
MAKES A PERFECT MATCH."

ENGLISH WHEEL FORMING MACHINE 

MSWO ENGLISH WHEEL FORMING MACHINE
        HEAVY DUTY
 
THROAT DEPTH 49¼"
 DISTANCE UPPER and LOWER CASTING 34"
 OPENING: Between rolls will vary depending on
        diameter of Top & Bottom Forming Rolls
        With 7-11/16" top & 3" diameter bottom 2¼"
 BOTTOM WHEEL HOLDER:
        Adjusts Up/Down by lower hydraulic cylinder
         connected to Hydraulic Pump.
        Rise & Fall is controlled by 2-Foot Electric Trips.

 
PRESSURE between Upper & Lower Forming Rolls is noted on
        Hydraulic Pressure Gage. Thus allows re-setting of thickness pressure.
 
HYDRAULIC POWER PACK: 1 hp 115 volts
 EQUIPPED WITH:
       (1) Top (Anvil) Flat Forming Roll 7-11⁄ 16" diameter x 3" wide
       (1) Top (Anvil) Flat Forming Roll 7¾” diameter x 3" wide
       (1) Bottom (Anvil) (Dome) Radius Forming Roll 6” diameter x 2" wide
       (1) Bottom (Anvil) (Dome) Radius Corners Forming Roll 5½” diameter x 2" wide  
       (1) Bottom (Anvil) Radius Corners (Narrow) Forming Roll 6" diameter x 1/2" wide
                 with Extra 6" diameter Radius Corner Roll x 7/16 wide.
       (1) Bottom (Anvil) Radius Corners Forming Roll 3½" diameter x 3" wide    
       (1) Bottom (Anvil) Flat Forming Roll 3” diameter x 3" wide  
       (1) Bottom (Anvil) Radius Corners Forming Roll 3" diameter x 3" wide    
       (1) Bottom (Anvil) Radius Corners Forming Roll 3" diameter x 3" wide    
       (1) Bottom (Anvil) Radius Forming Roll 3” diameter x 3" wide    

 
Inventory Reference S5160-10352  MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes
         MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo End to Side view with Lower Wheel Rise & Fall Hydraulic Pump & Tooling Photo End to Side view with Lower Wheel Rise & Fall Hydraulic Pump & Tooling.
MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo Wheel End to Side view with Lower Wheel Rise & Fall Hydraulic Pump & Tooling Photo Wheel End to Side view with Lower Wheel Rise & Fall Hydraulic Pump & Tooling.

        MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo Close-Up Upper & Lower Forming Wheels from end view Photo Close-Up view Upper & Lower Forming Wheels.
MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo Close-Up view Upper & Lower Forming Wheels from side to working end. Photo Close-Up view Upper & Lower Forming Wheels from side to working end.
         MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo Close-Up view Upper & Lower Forming Wheels from working end. Photo Close-Up view Upper & Lower Forming Wheels from working end.
MSWO ENGLISH WHEEL Heavy Duty FORMING MACHINE 49¼" THROAT DEPTH, DISTANCE UPPER and LOWER CASTING 34", OPENING: Between rolls will vary depending on diameter of Top & Bottom Forming Rolls with 7-11/16" top & 3" diameter bottom 2¼", BOTTOM WHEEL HOLDER Adjusts Up/Down by lower hydraulic cylinder connected to 1 hp 115 volt Hydraulic Pump  EQUIPPED WITH two top flat forming rolls and 8 Bottom (Anvil) Forming various sizes, Photo Close-Up Tooling and Hydraulic Lower Wheel (Anvil) Rise and Fall Pump Photo Close-Up Tooling and Hydraulic Lower Wheel (Anvil) Rise and Fall Pump
.






We are looking to buy one machine or entire manufacturing facility, 
PLEASE Fax or Email us your needs or what you have For-Sale
   
Telephone:  1-213-627-2847
    Fax:   1-213-627-2499
    Email:  sales@centurymachinery.com

 





   SHRINKERS and STRETCHERS  Kick type and Pneumatic Driven and Motorized
Manufactured by:  Erco,   TCE Erco,   HP Townsend,  Marchant  and Eckold
S5160-


The following are IN-STOCK
▼   ▼



MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 4A
 
    THROAT DEPTH 4"
 Equipped with 1-set Shrinking Jaws
  
Inventory Reference S5160-10103 marchant shrinker and stretcher machine, model 4A, pneumatic powered, throat depth 4", adjustable open height, with shrinking jaws, Serial Number 106, Photo Left Side to Front view   marchant shrinker and stretcher machine, model 4A, pneumatic powered, throat depth 4", adjustable open height, with shrinking jaws, Serial Number 106, Photo Left Side to Front view Photo Right Side to Front view.   marchant shrinker and stretcher machine, model 4A, pneumatic powered, throat depth 4", adjustable open height, with shrinking jaws, Serial Number 106, Photo Left Side to Front view
 
      marchant shrinker and stretcher machine, model 4A, pneumatic powered, throat depth 4", adjustable open height, with shrinking jaws, Serial Number 106, Photo Left Side to Front view Photo Right Side to Front view.   marchant shrinker and stretcher machine, model 4A, pneumatic powered, throat depth 4", adjustable open height, with shrinking jaws, Serial Number 106, Photo Left Side to Front view
 

 

 
 MARCHANT
Kick Type SHRINKER and STRETCHER Model 6F,
 
     THROAT DEPTH 6 inch
  Sold with 1-sets of
Stretcher Jaws
 
 
Inventory Reference S5160-10410  marchant shrinker and stretcher machine, model 6F, kick type, throat depth 6 inch, with stretching & shrinking jaws, Serial Number 357X  marchant shrinker and stretcher machine, model 6F, kick type, throat depth 6 inch, with stretching & shrinking jaws, Serial Number 357X, Photo front to right side view  Photo Front to Right Side.   marchant shrinker and stretcher machine, model 6F, kick type, throat depth 6 inch, with stretching & shrinking jaws, Serial Number 357X, Photo front to right side view
 
marchant shrinker and stretcher machine, model 6F, kick type, throat depth 6 inch, with stretching & shrinking jaws, Serial Number 357X, Photo close-up stretching jaws Photo close-up Stretching Jaws.   marchant shrinker and stretcher machine, model 6F, kick type, throat depth 6 inch, with stretching & shrinking jaws, Serial Number 357X, Photo close-up stretching jaws
 

 

 
MARCHANT Kick Type SHRINKER and STRETCHER Model 6FG,
      THROAT DEPTH 6 inch

  
Inventory Reference S5160-10409  marchant shrinker and stretcher machine, model 6FG, kick type, throat depth 6 inch, with stretching jaws, Serial Number 6A2923
  
         Use below photos as example of what you can expect
  
  marchant shrinker and stretcher machine, model 6FG, kick type,throat depth 6 inch,with stretching jaws, Serial Number 6A2923, Photo Right Side to Front view  Photo Right Side to Front view.    marchant shrinker and stretcher machine, model 6FG, kick type,throat depth 6 inch,with stretching jaws, Serial Number 6A2923, Photo Left Side to Front view  Photo Left Side to Front view.
  
        marchant shrinker and stretcher machine, model 6FG, kick type,throat depth 6 inch,with stretching jaws, Serial Number 6A2923, Photo Right Side view Rear to Right Side view.             
 

 
 
 
TCE CORP (Erco) Kick Type SHRINKER and STRETCHER Model 1447-6DT
 
    THROAT DEPTH 6"
 Equipped with:
     1-set of Shrinker Jaws.
     1-set of Stretching Jaws.

 
    Dovetail ways for quick change out of Jaws.
 
Inventory Reference  S5160-10436  TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332    TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Right Side Photo Right Side
 
TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Left Side Photo Left Side     TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Close-up Front view Stretcher Jaws Photo Close-up Front view Stretcher Jaws
 
         TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Close-up Left Side view Stretcher Jaws Photo Close-up Left Side view Stretcher Jaws    TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Close-up Right Side view Stretcher Jaws Photo Close-up Right Side view Stretcher Jaws
 
TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Close-up Right Side view Shrinker Jaws Photo Close-up  view Shrinker Jaws
 

 
 
 TCE ERCO
Kick Type SHRINKER and STRETCHER Model 1447
 
    THROAT DEPTH 6 inch
 Equipped with: 1-set of
Extended over-hang Shrinking Jaws
 
                Inventory Reference  S5160-10209       CLICK HERE FOR QUOTATION  TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-5
 
      CLICK HERE FOR PHOTO  TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-5, Photo Right Side to Front view Photo Right Side to Front view.      CLICK HERE FOR PHOTO  TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-5, Photo Close-up front view Shrinking Jaws Photo Close-up front view Shrinking Jaws.
 
CLICK HERE FOR PHOTO  TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-5, Photo Close-up side view Shrinking Jaws Photo Close-up side view Shrinking Jaws.      CLICK HERE FOR PHOTO  TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-5, Photo Close-up Front to Left Side view Shrinking Jaws Photo Close-up Front to Left Side view Shrinking Jaws.
 

 
 

 
TCE ERCO Kick Type SHRINKER and STRETCHER Model 1447
 
    THROAT DEPTH 6 inch
 Equipped with: 1-set of Standard Stretching Jaws

 
Inventory Reference  S5160-9995  CLICK HERE FOR QUOTATION  erco shrinker - stretcher, model 1447, kick type, throat depth 6 inch, with standard stretcher jaws, Serial Number 1357
 
CLICK HERE FOR PHOTO  erco shrinker - stretcher, model 1447, kick type, throat depth 6 inch, with standard stretcher jaws, Serial Number 1357, Photo Front to Right Side view
Photo Front to Right Side view.    CLICK HERE FOR PHOTO  erco shrinker - stretcher, model 1447, kick type, throat depth 6 inch, with standard stretcher jaws, Serial Number 1357, Photo Front to Right Side view Photo
 
 

 

 
ERCO
HP TOWNSEND Kick Type SHRINKER and STRETCHER Model 1447
 
    THROAT DEPTH 6 inch
 Equipped with: 1-set of
Extended over-hang Stretching Jaws
 
Inventory Reference  S5160-10214  CLICK HERE FOR QUOTATION  erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extension Overhang stretcher jaws, Serial Number 80380-2
 
erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781  or five sixty forth, with Extension Overhang stretcher jaws, Serial Number 80380-2, Photo Left side to Front view Photo Left Side Front view.     erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781  or five sixty forth, with Extension Overhang stretcher jaws, Serial Number 80380-2, Photo Left Side to Front view Stretching Jaws. Photo Left Side to Front view Stretching Jaws.
 
         erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781  or five sixty forth, with Extension Overhang stretcher jaws, Serial Number 80380-2, Photo close-up Right Side view extension stretching jaws Photo close-up Right Side view extension stretching jaws.
 
erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781  or five sixty forth, with Extension Overhang stretcher jaws, Serial Number 80380-2, Photo close-up Left Side view extension stretching jaws Photo close-up Left Side view extension stretching jaws.
 

 
 

 

 
 
 
       These Shrinker - Stretchers
 
       BELOW HAVE BEEN SOLD
 
 Please use as example of our finished products.
 
 ▼                  ▼                  ▼                           ▼
 
US
TOOL Kick Type SHRINKER and STRETCHER Model USPF150
 
    THROAT DEPTH 6 inch
 Equipped with:
     1-set Echold FWR407 Stretching Jaws
    
1-set Echold FWR405 Shrinker Jaws
 Inventory Reference 
S5160- 
  us tool shrinker and stretcher machine_model USPF150_kick type_capacity 16 gauge mild steel_14 gauge aluminum_throat reach 6"_gap 3½"_stroke of ram adjustable_equipped with 1-set echold FWA405 shrinker jaws_1-set echold FWR407 stretcher jaws_Serial Number 2001 Photo Left Side to Front.
 
 "This unit sold,  Call or Email to be placed onto wanted list"
 
 
 

 
TCE CORP (Erco) Kick Type SHRINKER and STRETCHER Model 1447-6DT
 
    THROAT DEPTH 6"
 Equipped with:
     1-set of
Shrinker Jaws  with wide platform.
 
    Dovetail ways for quick change out of Jaws.
 
Inventory Reference  S5160-10135
  TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo Right Side Photo right side.
 
       TCE Erco shrinker stretcher, model 1447-6DT, kick type, throat depth 6 inch, with shrinker jaws with wide platform, mounted on dovetailed ways, Serial Number 84332, Photo close-up Shrinker Jaws right side showing dovetailed mount Photo close up view Shrinker Jaws right side showing Dovetailed mount.
 
 "This unit sold,  Call or Email to be placed onto wanted list"
 
 
 

 
TCE ERCO Kick Type SHRINKER and STRETCHER Model 1447
 
    THROAT DEPTH 6 inch
 Equipped with: 1-set of
Extended over-hang Shrinking Jaws
                Inventory Reference 
S5160-10213

 
      TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-3, Photo Right Side to Front view Photo Right Side to Front view.       TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-3, Photo Close-up Right Side view Shrinking Jaws. Photo Close-up Right Side view Shrinking Jaws.
 
TCE erco kick type shrinker and stretcher machine, model 1447, throat depth 6 inch, capacity 0.0781 or five sixty forth, with Extended Overhang shrinking jaws, Serial Number 80620-3, Photo Close-up Front Side view Shrinking Jaws Photo Close-up Front Side view Shrinking Jaws.
 
 "This unit sold,  Call or Email to be placed onto wanted list"
 

 
 

 
 MARCHANT Kick Type SHRINKER and STRETCHER Model 4F,
      THROAT DEPTH 4 inch
  
Inventory Reference S5160-9328   marchant shrinker and stretcher, model 4FG, kick type, throat depth 4 inch, with shrinking jaws set
 
"This unit sold,  Call or Email to be placed onto wanted list"
 

 

 

 
"This unit sold,  Call or Email to be placed onto wanted list"
 MARCHANT
Pneumatic Powered SHRINKER and STRETCHER  Model 4A
  
    THROAT DEPTH 4"
  Equipped with 1-set Shrinking Jaws
   
Inventory Reference S5160-10357 
marchant shrinker and stretcher machine, model 4A, pneumatic powered, capacities tensile strength 70,000 pounds_aluminum alloy 24ST ¼" thick x 1½" width, aluminum alloy 24SO 5/16" thick x 2" width, stainless steel 3/16" thick x 1½" width, titanium 5/32" thick x 1" width, throat depth to front of jaws 4", stroke of ram ¼", adjustable open height, pneumatic actuated by foot peddle, equipped with shrinking jaws, Serial Number 113
 THESE PHOTOS are of another Marchant , "This is what you can expect"
 
 marchant shrinker and stretcher machine, model 4A, pneumatic powered, capacities tensile strength 70,000 pounds_aluminum alloy 24ST ¼" thick x 1½" width, aluminum alloy 24SO 5/16" thick x 2" width, stainless steel 3/16" thick x 1½" width, titanium 5/32" thick x 1" width, throat depth to front of jaws 4", stroke of ram ¼", adjustable open height, pneumatic actuated by foot peddle, equipped with shrinking jaws, Serial Number113, Photo Right Side to Front view
  Photo Right Side to Front view.      marchant shrinker and stretcher machine, model 4A, pneumatic powered, capacities tensile strength 70,000 pounds_aluminum alloy 24ST ¼" thick x 1½" width, aluminum alloy 24SO 5/16" thick x 2" width, stainless steel 3/16" thick x 1½" width, titanium 5/32" thick x 1" width, throat depth to front of jaws 4", stroke of ram ¼", adjustable open height, pneumatic actuated by foot peddle, equipped with shrinking jaws, Serial Number113,  Photo Right Side to Front view  Photo Right Side to Front view.
 
 
 
 
MARCHANT Kick Type SHRINKER and STRETCHER Model 6F,
 
     THROAT DEPTH 6 inch
  Sold with 1-sets of
Stretcher Jaws
 
 
Inventory Reference S5160-9652   marchant shrinker stretcher, model 4F, with Stretcher jaws, Mfg 2001 Photo Over-all view.   marchant shrinker stretcher, model 4F, with Stretcher jaws, Mfg 2001 Photo Close up Stretcher Jaws.
 
 "This older style unit sold,  Call or Email to be placed onto wanted list"
 


 
 
MARCHANT Kick Type SHRINKER and STRETCHER Model 6FG,
      THROAT DEPTH 6 inch

  Inventory Reference S5160-10040 
CLICK HERE FOR QUOTATION  marchant shrinker and stretcher machine_model 6FG_ kick type_throat depth 6 inch_with stretching jaws_Serial Number 6A2923
 CLICK HERE FOR PHOTO marchant shrinker and stretcher machine, model 6FG, kick type,throat depth 6 inch,with stretching jaws, Serial Number 6A2923, Photo Right Side to Front view Photo Right Side to Front view
Photo Left Side to Front view.
 
 marchant shrinker and stretcher machine, model 6FG, kick type,throat depth 6 inch,with stretching jaws, Serial Number 6A2923, Rear to Right Side view  Rear to Right Side view.
 
 "This unit sold,  Call or Email to be placed onto wanted list"
 

 
 
 
 MARCHANT Pneumatic Power
SHRINKER and STRETCHER Model 6A,
 
     THROAT DEPTH 6"
  
Inventory Reference S5160-10200   marchant pneumatic powered shrinker and stretcher, model 6A, throat depth 6 inch, with shrinking and stretching jaw sets   marchant pneumatic powered shrinker and stretcher, model 6A, throat depth 6 inch, with shrinking and stretching jaw sets    marchant pneumatic powered shrinker and stretcher, model 6A, throat depth 6 inch, with shrinking and stretching jaw sets
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 
 
MARCHANT
Pneumatic Powered SHRINKER and STRETCHER  Model 6A
 
THROAT DEPTH 6"
 
This shrinker stretcher is mounted on portable tilting frame.
    Tilting forward or backward by hand crank thru gear box.
    Unit can be locked in three positions forward or backwards
    where jaws face standard position, 45° forward back and
    Up or Down.

 
Inventory Reference
S5160-10206  MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo Left Side to  Front Photo Left Side to Front.  MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo Right Side to Front Photo Right Side to Front.
 
MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo Rear at Tilt Crank Hand Wheel Photo Rear at Tilt Crank Hand Wheel.     MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo side view with marchant tilted forward at 45 degrees. Photo side view with Marchant tilted forward at 45 degrees.
 
      
MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo close-up Shrinker Jaws assemblies Photo close-up Shrinker Jaws.     MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo close-up left side to front view Shrinker Jaws  Photo close-up left side to front view Shrinker Jaws.
 
 MARCHANT Pneumatic Powered SHRINKER and STRETCHER  Model 6A, THROAT DEPTH 6" This shrinker stretcher is MOUNTED ON PORTABLE TILTING FRAME. Tilting forward or backward by hand crank thru gear box. Unit can be locked in 3-positions forward or backwards where jaws face standard position, 45° forward back and Up or Down. Equipped with1-set Shrinker Jaws. CAPACITY Aluminum Alloy 2424, 1/4" thick x 1½" width, Aluminum Alloy 2452, 1/4" thick x 2" width, Stainless Steel, 5/32" thick x 1½" width, Titanium, 5/32" thick x 1" width, Photo close-up front to right side view Shrinker Jaws Photo close-up Front to Right side view Shrinker Jaws.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 
 ECKOLD
  POWER SHRINKER - STRETCHER - PLANISHER & DOMING MACHINE
 
  Kraftformer     Model KF 170 PD    Pneumatic Type
 
   
THROAT DEPTH 6.693"
 I
nventory Reference S5160-
 
eckold kraftformer, power shrinker - stretcher - planisher, model KF170PD, throat depth 6.7 inch, single & continuous stroke, with 3-sets shrinking jaws, 2-sets stretching jaws, Serial Number1501, Left Side to Front Photo Left Side to Front view.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 
 
TCE CORP (Erco) Kick Type SHRINKER and STRETCHER Model 1447-12DT
 
    THROAT DEPTH 12"
 Equipped with:
      1-set of Stretcher Jaws (Dove tail mount)

 
Inventory Reference  S5160-
 
TCE erco shrinker-stretcher, model 1447-12DT, kick type, throat 12 in, with stretch jaws, Photo Front to Right Side Photo Right Side to Front.    TCE erco shrinker-stretcher, model 1447-12DT, kick type, throat 12 in, with stretch jaws, Photo close-up Wide Platform Stretcher Jaws. Photo close-up Wide Platform Stretcher Jaws.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 

 
 
 MARCHANT 
Pneumatic Power
SHRINKER and STRETCHER Model 12A
 
    THROAT DEPTH 12"
 
Equipped with: 1-set of Stretching Jaws

 I
nventory Reference S5160-101102   marchant shrinker and stretcher machine, model 12A, pneumatic powered, throat depth 12",  stroke of ram ¼", adjustable open height, pneumatic actuated by foot peddlealuminum alloy 2024 5/32" thick x 1½" width, aluminum alloy 5052  3/16" thick x 1" width, stainless steel 3/32" thick x 1" width, titanium 3/32" thick x 3/4" width, equipped with one set of stretcher jaws 
 
marchant shrinker and stretcher machine, model 12A, pneumatic powered, capacities tensile strength 70,000 pounds, aluminum alloy 2024 5/32" thick x 1½" width, aluminum alloy 5052  3/16" thick x 1" width, stainless steel 3/32" thick x 1" width, titanium 3/32" thick x 3/4" width, throat depth to front of jaws 12", stroke of ram ¼", with stretcher jaws, Serial Number 71, Photo Right Side to Front Photo Right Side to Front.        marchant shrinker and stretcher machine, model 12A, pneumatic powered, capacities tensile strength 70,000 pounds, aluminum alloy 2024 5/32" thick x 1½" width, aluminum alloy 5052  3/16" thick x 1" width, stainless steel 3/32" thick x 1" width, titanium 3/32" thick x 3/4" width, throat depth to front of jaws 12", stroke of ram ¼", with stretcher jaws, Serial Number 71, Photo Left Side to Front Photo Left Side to Front.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 
 
MARCHANT HYDRAULIC POWER SHRINKER and STRETCHER Model 12H
  
 THROAT DEPTH 12"
 CAPACITY:  3/8" x 2" wide Aluminum 2024,    1/4" x 2" wide  Aluminum 5052,   
                    1/4" x 2" wide Stainless Steel, 
    3/16" Stainless Steel
 HYDRAULIC PUMP 7½ HP

 
Equipped with: 1-set of Stretching 2" x 4" Jaws
 and Assembly 
                           
1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws
and Assembly
                          
 1-set of Shrinker 2" x 4" Jaws  and Assembly
                           
1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly
                           
1-set of Stretching 2" x 4" Top & Bottom Jaws
                           
1-set of Shrinking 2" x 4" Top & Bottom Jaws

                           
1-set of True Radius Stretching Top & Bottom Jaws
                          
 1-set of True Radius Shrinking Top & Bottom Jaws
 I
nventory Reference S5160-10418   MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg  MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Front to Right Side Photo Front to Right Side.  
  
MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Right Side Photo Right Side.    MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Front to Left Side to Front Photo Left Side to Front.    MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Close-up Controls & Jaws Photo Close-up Controls & Jaws. Side.
  
     MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Close-up Stretcher Jaws Photo Close-up Stretcher Jaws.    MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Close-up throat Plates with dimensions. Photo Close-up Throat Plates with dimensions. 
 
MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Close-up Tooling Photo Close-up Tooling.     MARCHANT Model 12H, HYDRAULIC POWER SHRINKER and STRETCHER  THROAT DEPTH 12", Equipped with: 1-set of Stretching 2" x 4" Jaws and Assembly,1-set of Overhang Stretching 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Shrinker 2" x 4" Jaws  and Assembly, 1-set of Overhang Shrinking 3.75" FB x 3.5"LR Jaws and Assembly, 1-set of Stretching 2" x 4" Top & Bottom Jaws, 1-set of Shrinking 2" x 4" Top & Bottom Jaws, 1-set of True Radius Stretching Top & Bottom Jaws, 1-set of True Radius Shrinking Top & Bottom Jaws, Misc Spare Tlg, Photo Close-up Tooling Photo Close-up Tooling.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 
 
ECKOLD  POWER SHRINKER - STRETCHER - PLANISHER & DOMING MACHINE
 Piccolo
Kraftformer     Model 320
 
   
THROAT DEPTH 14"
 
Inventory Reference S5160-
 eckold piccolo kraftformer, power shrinker - stretcher - planisher machine, model KF320-74AC, throat depth 14 inch, with shrinking - stretching - planishing & doming  jaw sets, Serial Number154-4549, Left Side to Front view Photo Left Side to Front view.
 
"This unit sold,  Call or Email to be placed onto wanted list"
 
 
 

 ERCO
POWER SHRINKER and STRETCHER Model 476
 
Motor Driven
    
THROAT DEPTH: Front of Jaws 18¾"
 CAPACITY 5/64"      Tensile Strength 70,000 lbs
 STROKES PER MINUTE two speed ranges 150 and 300
 
EQUIPPED WITH:
    
1-set STRETCHER JAWS " Jaw extension front and back Over-all Jaw size 2¾" front to back x 2" width
            Stippled area 2¾" front to back x 1 width

 
    1-set Shrinking Jaws with New Lower one piece anvil  and Upper one piece anvil.
 
           with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil.
 
Inventory Reference
S5160-10050 ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227
 
ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227, Photo Front view Photo Front view.    CLICK HERE FOR PHOTO  ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH: Front of Jaws 18¾",  ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp,220v, Two Speeds 900 & 1800 rpm. EQUIPPED WITH 1-set STRETCHER JAWS " Jaw extension front and back Over-all Jaw size 2¾" front to back x 2" width, Stippled area 2¾" front to back x 1 width, 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Momentary On Foot Switch, Motor Two Speed Switch, Serial Number 227, Photo Left Side to Front view Photo Left Side to Front view.    CLICK HERE FOR PHOTO  ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH: Front of Jaws 18¾",  ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp,220v, Two Speeds 900 & 1800 rpm. EQUIPPED WITH 1-set STRETCHER JAWS " Jaw extension front and back Over-all Jaw size 2¾" front to back x 2" width, Stippled area 2¾" front to back x 1 width, 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Momentary On Foot Switch, Motor Two Speed Switch, Serial Number 227, Photo Left Side to Rear view Photo Left Side to Rear view
 
          ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227, Photo Close-Up New Stretcher Jaws and one piece top & bottom Anvils from front to right side. Photo Close-Up New Stretcher Jaws and one piece top & bottom Anvils from front to Right Side.
 
ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227, Photo Close-Up New Stretcher Jaws and one piece top & bottom Anvils from front to Left Side. Photo Close-Up New STRETCHER JAWS and one piece top & bottom Anvils from front to Left Side.
 
         ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227, Photo Close-Up New Stretcher Jaws and one piece top & bottom Anvils Right Side view Photo Close-Up New STRETCHER JAWS and one piece top & bottom Anvils Right Side view.
 
ERCO POWER SHRINKER & STRETCHER MACHINE, Model 476, Serial Number 227, CAPACITY 5/64", THROAT DEPTH Front of Jaws 18¾", ADJUSTMENT OF LOWER ANVIL up and down 5/16", STROKES PER MINUTE 150 and 300, MOTOR DRIVE 1 hp, 2-Speeds 900 & 1800 rpm, WITH 1-set STRETCHER JAWS " 1-set Shrinking Jaws with New Lower one piece anvil and Upper one piece anvil., with one New Lower one piece Jaw Anvil and one New Upper one piece Jaw Anvil., LOWER JAW Base (Anvil) ONE PIECE  adjusts up and down, Serial Number 227, Photo Close-Up New Stretcher Jaws and one piece top & bottom Anvils Right Side view Photo Close-Up New SHRINKER JAWS and one piece top & bottom Anvils Right Side view.
 

 
 
 ECKOLD
POWER SHRINKER STRETCHER and PLANISHER MACHINE

 Model KF 653C
 THROAT DEPTH REACH  26"
 Inventory Reference S5160-  
  ECKOLD POWER SHRINKER – STRETCHER MACHINE, Model KF 653C, THROAT DEPTH REACH 26", RAM ADJUSTMENT by Hand Wheel 3⅜", STROKES PER MINUTE 150. 300, 600, FORMING CAPACITY Deep drawing Steel 400 N / 6.0 mm. 0.2362" (16/64”), Aluminum 250 N / 8.0 mm 0.31496" (21/64”),Stainless Steel 600 N / 4 mm 0.15748" (5/32), Three Speeds MOTOR DRIVE Wired 420 volts, 3-phase, 50 htz  KW 3.1, KW 3.0, KW 3.1, WITH 1-set Shrinker Jaws, 1-set Stretcher Jaws, Serial Number 92-6461, Photo Front to Left Side view
Photo Front to Left Side view.
 
ECKOLD POWER SHRINKER – STRETCHER MACHINE, Model KF 653C, THROAT DEPTH REACH 26", RAM ADJUSTMENT by Hand Wheel 3⅜", STROKES PER MINUTE 150. 300, 600, FORMING CAPACITY Deep drawing Steel 400 N / 6.0 mm. 0.2362" (16/64”), Aluminum 250 N / 8.0 mm 0.31496" (21/64”),Stainless Steel 600 N / 4 mm 0.15748" (5/32), Three Speeds MOTOR DRIVE Wired 420 volts, 3-phase, 50 htz  KW 3.1, KW 3.0, KW 3.1, WITH 1-set Shrinker Jaws, 1-set Stretcher Jaws, Serial Number 92-6461,, Photo Front to Right Side view
Photo Front to Right Side view.    ECKOLD POWER SHRINKER – STRETCHER MACHINE, Model KF 653C, THROAT DEPTH REACH 26", RAM ADJUSTMENT by Hand Wheel 3⅜", STROKES PER MINUTE 150. 300, 600, FORMING CAPACITY Deep drawing Steel 400 N / 6.0 mm. 0.2362" (16/64”), Aluminum 250 N / 8.0 mm 0.31496" (21/64”),Stainless Steel 600 N / 4 mm 0.15748" (5/32), Three Speeds MOTOR DRIVE Wired 420 volts, 3-phase, 50 htz  KW 3.1, KW 3.0, KW 3.1, WITH 1-set Shrinker Jaws, 1-set Stretcher Jaws, Serial Number 92-6461,, Photo Right Side view Photo Right Side view.
 
"This unit sold,  Call or Email to be placed onto wanted list"





 

   STRETCH WRAP FORMING MACHINES, STRETCH PRESS,
Mfg'd. by  Cyril Bath and L&F Hufford  Sheridan Gray S8120-

SHEET STRETCH FORMER
Capabilities: Stretch Level - Stretch Wrap - Drape & Extrusion Stretch Forming
Mfg'd. by  Sheridan Gray 
S8120-

RADIAL DRAW FORMING MACHINES
Cyril Bath - Hufford - L&F - Sheridan Gray

STRETCH DRAW FORMING PRESS  -  COMPRESSION FORMING
Sheridan Gray Stretch Draw Press SDP-250-120-60-150   (This item is at bottom of list, USE THIS SCROLL BAR TO SCROLL TO ITEM ▬▬▬►


 *SHEET & EXTRUSION STRETCH FORMER, Mfg'd by Sheridan Gray, Cyril Bath, L&F Hufford
 *RADIAL DRAW STRETCH FORMING*   *COMPRESSION FORMING*
 *CONTOUR STRETCH FORMERS*
  Mfg'd by Cyril Bath - Sheridan Gray & Hufford
*STRETCH DRAW FORMING PRESS*  Mfg'd by Sheridan Gray


(This item is located at bottom of list.)

                                           USE THIS SCROLL BAR TO MOVE THRU LIST▬▬▬▬▬▬▬▬▬▬▬►

 

The following are EXTRUSION STRETCH WRAP FORMERS:
                                                                                     
 

NAS PLANT HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
                FORMING TONNAGE 11

DISTANCE BETWEEN JAWS:

     Maximum Length of Part with Tension Cylinders
          fully retracted 136" (3,454.4 mm)
     Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm)
TENSION CYLINDER STROKE each with 3" long spacer to reduce stroke to 7" (177.6mm)
TENSION CYLINDER ROTATION +/- 25 Degrees
ARMS: SWING Simultaneous Arm Motion Arm swings 10° Forward to 90°Back.
DIE TABLE: Working Surface 35⅝" width x 35¾" depth (908.88 x 908.05 mm)
Hydraulic Pump 10 hp.
EQUIPPED WITH:
       1- set 3" Jaws with Pneumatic Clamping.
       17- Miscellaneous sets of Gripper Jaws
       7- single Gripper Jaws
Inventory Reference S8120-10423 
11 ton NAS PLANT DIVISION STRETCH WRAP FORMING PRESS, Maximum Length of Part with Tension Cylinders fully retracted 136", Minimum Length of Part with Tension Cylinders fully extended 10", Each Tension Cylindrical Stroke 13″, Tension Cylinder Rotation +/- 25 Degrees, Arm swing Simultaneous 10° Forward to 90° Back, Wrapping Speed adjustable, Die Table Surface x 35⅝" W x 35¾" D, 75-pre drilled & threaded)  5/8", Hydraulic Pump 10 hp, EQUIPPED WITH 1- set 3" Jaws with Pneumatic Clamping, 17- Miscellaneous sets of Gripper Jaws, 7- single Gripper   11 ton NAS PLANT DIVISION STRETCH WRAP FORMING PRESS, Maximum Length of Part with Tension Cylinders fully retracted 136", Minimum Length of Part with Tension Cylinders fully extended 10", Each Tension Cylindrical Stroke 13″, Tension Cylinder Rotation +/- 25 Degrees, Arm swing Simultaneous 10° Forward to 90° Back, Wrapping Speed adjustable, Die Table Surface x 35⅝" W x 35¾" D, 75-pre drilled & threaded)  5/8", Hydraulic Pump 10 hp, EQUIPPED WITH 1- set 3" Jaws with Pneumatic Clamping, 17- Miscellaneous sets of Gripper Jaws, 7- single Gripper, Photo Front Photo Front view.
  11 ton NAS PLANT DIVISION STRETCH WRAP FORMING PRESS, Maximum Length of Part with Tension Cylinders fully retracted 136", Minimum Length of Part with Tension Cylinders fully extended 10", Each Tension Cylindrical Stroke 13″, Tension Cylinder Rotation +/- 25 Degrees, Arm swing Simultaneous 10° Forward to 90° Back, Wrapping Speed adjustable, Die Table Surface x 35⅝" W x 35¾" D, 75-pre drilled & threaded)  5/8", Hydraulic Pump 10 hp, EQUIPPED WITH 1- set 3" Jaws with Pneumatic Clamping, 17- Miscellaneous sets of Gripper Jaws, 7- single Gripper, Photo Left side to Front Photo Left side to Front.    11 ton NAS PLANT DIVISION STRETCH WRAP FORMING PRESS, Maximum Length of Part with Tension Cylinders fully retracted 136", Minimum Length of Part with Tension Cylinders fully extended 10", Each Tension Cylindrical Stroke 13″, Tension Cylinder Rotation +/- 25 Degrees, Arm swing Simultaneous 10° Forward to 90° Back, Wrapping Speed adjustable, Die Table Surface x 35⅝" W x 35¾" D, 75-pre drilled & threaded)  5/8", Hydraulic Pump 10 hp, EQUIPPED WITH 1- set 3" Jaws with Pneumatic Clamping, 17- Miscellaneous sets of Gripper Jaws, 7- single Gripper, Photo Gripper Jaws Photo extra Gripper Jaws.

 

 

L&F HUFFORD HORIZONTAL CNC Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A-5
FORMING TONNAGE 12
DISTANCE BETWEEN JAWS 115" (2,921 mm)
ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back.
DIE LENGTH at FULL TONNAGE and 180 degrees Wrap:
       Minimum 11" (279.4 mm)          Maximum 40" (1,016 mm)
DIE TABLE: 48 Pre drilled & threaded
Working Surface 42" W x 44¾" D (1,066.8 mm X 1,136.65 mm)
HYDRAULIC PUMP MOTOR DRIVE: 30 H.P.
CONTROLS: DeMott CNC Controls with: Programmable Key Pad, CRT, and
     Hand Function Buttons.
REMOTE HAND CONTROLS located on each arm with 2-Tension Cyl. In/Out push buttons,
      Tension Cylinder Load and Stop Push Buttons. Jaw Close / Open Switch. Carriage In / Out Switch.
EQUIPPED WITH:
 1-set of 4" Jaws with Hydraulic Clamping.       1-set Adjustable Die Post.
 Farval Centralized Lubrication System SS-4200.  Thermal Transfer Products Heat Exchanger.
Inventory Ref: S8120-10259   CLICK HERE FOR QUOTATION  L&F HUFFORD CNC EXTRUSION STRETCH WRAP FORMING MACHINE, Model A-5, FORMING TONNAGE 12, DISTANCE BETWEEN JAWS 115" (2,921 mm), set of 4" Jaws with Hydraulic Clamping, TENSION CYLINDERS STROKE 20" (508 mm), TENSION CYLINDER SWING (Horizontal Elongation) +/- 30°, ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back., WRAPPING SPEED RANGE Adjustable, DIE LENGTH at FULL TONNAGE and 180 degrees Wrap adjustable Min 11" (279.4 mm) Max 40" (1,016 mm), DIE TABLE 42"FB x 44¾" LR (1,066.8 mm x 1,136.65 mm) Pre drilled & threaded, MOTOR DRIVE 30 H.P , Hydraulic Pump, Joggler Pump 7½ H.P, two Arm Adjustment each 1/2 H.P, CONTROLS DeMott CNC Controls, REMOTE HAND CONTROLS located on each arm, EQUIPPED WITH 1-set Adjustable Die Post, Farval Centralized Lubrication System, Heat Exchanger, Serial Number 81127-1
L&F HUFFORD CNC EXTRUSION STRETCH WRAP FORMING MACHINE, Model A-5, FORMING TONNAGE 12, DISTANCE BETWEEN JAWS 115" (2,921 mm), set of 4" Jaws with Hydraulic Clamping, TENSION CYLINDERS STROKE 20" (508 mm), TENSION CYLINDER SWING (Horizontal Elongation) +/- 30°, ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back., WRAPPING SPEED RANGE Adjustable, DIE LENGTH at FULL TONNAGE and 180 degrees Wrap adjustable Min 11" (279.4 mm) Max 40" (1,016 mm), DIE TABLE 42"FB x 44¾" LR (1,066.8 mm x 1,136.65 mm) Pre drilled & threaded, MOTOR DRIVE 30 H.P , Hydraulic Pump, Joggler Pump 7½ H.P, two Arm Adjustment each 1/2 H.P, CONTROLS DeMott CNC Controls, REMOTE HAND CONTROLS located on each arm, EQUIPPED WITH 1-set Adjustable Die Post, Farval Centralized Lubrication System, Heat Exchanger, Serial Number 81127-1, Photo Left Side over-all view Photo Left Side over-all view.     L&F HUFFORD CNC EXTRUSION STRETCH WRAP FORMING MACHINE, Model A-5, FORMING TONNAGE 12, DISTANCE BETWEEN JAWS 115" (2,921 mm), set of 4" Jaws with Hydraulic Clamping, TENSION CYLINDERS STROKE 20" (508 mm), TENSION CYLINDER SWING (Horizontal Elongation) +/- 30°, ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back., WRAPPING SPEED RANGE Adjustable, DIE LENGTH at FULL TONNAGE and 180 degrees Wrap adjustable Min 11" (279.4 mm) Max 40" (1,016 mm), DIE TABLE 42"FB x 44¾" LR (1,066.8 mm x 1,136.65 mm) Pre drilled & threaded, MOTOR DRIVE 30 H.P , Hydraulic Pump, Joggler Pump 7½ H.P, two Arm Adjustment each 1/2 H.P, CONTROLS DeMott CNC Controls, REMOTE HAND CONTROLS located on each arm, EQUIPPED WITH 1-set Adjustable Die Post, Farval Centralized Lubrication System, Heat Exchanger, Serial Number 81127-1, Photo Front to Left Side view Photo Front to Left Side view.
L&F HUFFORD CNC EXTRUSION STRETCH WRAP FORMING MACHINE, Model A-5, FORMING TONNAGE 12, DISTANCE BETWEEN JAWS 115" (2,921 mm), set of 4" Jaws with Hydraulic Clamping, TENSION CYLINDERS STROKE 20" (508 mm), TENSION CYLINDER SWING (Horizontal Elongation) +/- 30°, ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back., WRAPPING SPEED RANGE Adjustable, DIE LENGTH at FULL TONNAGE and 180 degrees Wrap adjustable Min 11" (279.4 mm) Max 40" (1,016 mm), DIE TABLE 42"FB x 44¾" LR (1,066.8 mm x 1,136.65 mm) Pre drilled & threaded, MOTOR DRIVE 30 H.P , Hydraulic Pump, Joggler Pump 7½ H.P, two Arm Adjustment each 1/2 H.P, CONTROLS DeMott CNC Controls, REMOTE HAND CONTROLS located on each arm, EQUIPPED WITH 1-set Adjustable Die Post, Farval Centralized Lubrication System, Heat Exchanger, Serial Number 81127-1, Photo Down view Table, Jaws, Die Post Photo Down view Table, Jaws, and Adjustable Die Post.



HUFFORD HORIZONTAL
Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A5

Tension Cylinders  Pull 11½ tons
   Distance between Jaws Clamp: Maximum 115"
      with 4" Jaws
Die length at full
tonnage and 180 degree bend: Minimum 11"  Maximum 40"
Inventory Reference
S8120-10625




CYRIL BATH  CNC HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model V-10    QUAD AXIS
CNC Controls

Tension Cylinders  Pull 10 tons
Distance between Gripper Jaws Clamp:  Maximum 113" (2,870.2mm)
     
                                                                 Minimum 27" (685.8mm)
Arm  SWING BACK 82 degrees
Tension Cylinder Stroke 43"
GRIPPER JAWS ROTATION 180 degrees
      Swings Left/Right +/-25 degrees  TILT +/-10 degrees

GRIPPER JAWS CARRIAGE with Rise and Fall
EQUIPPED WITH:
    Operator CNC Controls and Manual Controls
    Nova Gantry Die Changeover system with Rotary Table
    Four Hydraulic Tool Clamps
Inventory Reference
S8120-10233 CLICK HERE FOR QUOTATION  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct. 2001
CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct. 2001, Photos taken in plant prior to Stretch Former being decommissioned Photos with-in taken in plant prior to Stretch Former being decommissioned.

PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct. 2001, Photos taken in plant prior to Stretch Former being decommissioned Photos with-in taken in plant prior to Stretch Former being decommissioned.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct. 2001, Photo Front View Work Area Photo Front view Work Area.        CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Front to Right Side Photo Front to Right Side.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Close-up Die Holders and Quad Jaw Holders Photo Close-up Die Holders and Quad Jaw Holders.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Down View Table and four Die Clamps.    Photo Down View Table and 4-Die Clamps.     PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo side viewJaw Holder and 4- Die Clamps Photo side view Jaw Holder and 4-Die Clamps.
 CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Control Counsel with CRT, Program Keyboard and Operation Hand Controls  Photo Control Counsel with CRT, Program Keyboard and Operation Hand Controls.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Hydraulic Power Unit Photo Hydraulic Power Unit
.     CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Rear view right side with Hydraulic Power Pack & Electric Power Knife Switch Photo rear view right side with Hydraulic Power Pack & Electric Power Knife Switch.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Control Cabinet and Hydraulic Power Unit.
Photo Control Cabinet and Hydraulic Power Unit.         CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Trabon Maxi Monitor Mark 111, Lubriquip. Photo Trabon Maxi Monitor Mark 111, Lubriquip.
CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo view looking up at Nova Gantry Die Changeover.
Photo view looking up at Nova Gantry Die Changeover.    CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Partial view of Nova Die Changeover motor drives. Photo Partial view of Nova Die Changeover motor drives.
PHOTO  CYRIL BATH CNC EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model V10, QUAD AXIS, FORMING TONNAGE 10, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 113" 2,870.2 mm, Minimum Length of Part with Tension Cylinders fully extended 27" 685.8 mm, TENSION CYLINDER STROKE 43" 1,092.2 mm, GRIPPER JAW AXIAL ROTATION +/- 180 Degrees, GRIPPER IN High Operation position 14-916" 380.05mm, Low operation position 19-9/16" 496.89mm Load position 20-13/16" 528.64mm,CENTER OF TENSION CYLINDER CARRIAGE PIVOT  to TOP OF ARM: High Operation height  23½" 647.7mm, Low Operation height bottom of Gripper 18½" 469.9mm, Load Position 17¼" 438.15mm, TENSION CYLINDER MOVEMENT Rise and Fall, Swings: 25° Back and Forward 25° and Tilts UP / Down Up +/- 10°, ARM SWING BACK each Arm has Independent Movement 82 DEGREES, DIE TABLE: 25 Pre drilled & threaded, Working Surface 56" W x 41" D 1,422.4 x1041.4mm, MOTOR DRIVE Hydraulic Pump 25 H.P, CONTROLS CNC Controls with: Programmable Key Pad, CRT, and Hand Function Buttons. Remote Stop Buttons on each arm, EQUIPPED WITH Hydraulic Gripper Jaws, 4-Hydraulic Tool Clamps, Heat Exchanger, Nova Gantry Die Changeover system with Rotary Table, Serial Number 101104, Mfg Oct 2001, Photo Nova Die Changeover Part Turn Table. Photo Nova Die Changeover Part Turn Table.



CYRIL BATH
HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Tension Cylinders  Pull 12½ tons
   Distance between Jaws Clamp: Maximum 120"
      with 6" Jaws
Inventory Reference
S8120-10026



HUFFORD HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A10

Tension Cylinders  Pull 17½ tons
Distance between Jaws Clamp: Maximum 219" (5562.6mm)
      with 4" Jaws

Die length at full
tonnage and 180 degree bend: Minimum 20"  Maximum 68"
Inventory Reference
S8120-10025  HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 219" (5562.6 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 4” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number H081    HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 219" (5562.6 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 4” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number H081, Photo Front to Left Side Photo Front Left Side View.
PHOTO  HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 219" (5562.6 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 4” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number H081, Photo Hydraulic Pump and Left Side View  Photo Hydraulic Pump and Left Side View.



HUFFORD HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A10

Tension Cylinders  Pull 17½ tons
Distance between Jaws Clamp: Maximum 205" (5207mm)
      with 6" Jaws

Die length at full
tonnage and 180 degree bend: Minimum 20"  Maximum 68"
Inventory Reference
S8120-10220  HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 205" (5207 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 6” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number 79
PHOTO  HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 205" (5207 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 6” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number 79, Photo Left Side to Front  Photo Left Side to Front View.      PHOTO  HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 205" (5207 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 6” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number 79, Photo Front to Right Side.   Photo Front to Right Side.
     
 HUFFORD EXTRUSION STRETCH WRAP FORMER, STRETCH FORMING PRESS, Model A-10, FORMING TONNAGE 17½, DISTANCE BETWEEN JAWS: Maximum Length of Part with Tension Cylinders fully retracted 205" (5207 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), Equipped with 6” Jaws with Hydraulic Clamping, TENSION CYLINDER STROKE each 18½″, TENSION CYLINDER ROTATION +/- 25 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10° Forward to 90°Back, WRAPPING SPEED RANGE Adjustable, DIE LENGTH at full tonnage and 180° bend: Minimum 20" (508 mm), Maximum 68" (1727.2 mm), DIE TABLE:  (Pre drilled & threaded) 5/8", Working Surface 65" W x 30" D (1651 x 762 mm), Height Table To Floor 35" (889 mm), MOTOR DRIVE: 15 H.P, Serial Number 79, Photo Close Up 6 inch Jaws   Photo Close Up 6 inch Jaws.



CUSTOM
HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Tension Cylinders  Pull 19 tons
Distance between Jaws Clamp: Maximum 218 (5237.2mm)
      with 4" Jaws

Die length at full
tonnage and 180 degree bend: Minimum 20"  Maximum 72"
Inventory Reference
S8120-10218 CUSTOM STRETCH WRAP FORMER, STRETCH FORMING PRESS, FORMING TONNAGE 18, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 218" (5537.2 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), TENSION CYLINDER STROKE each 24”  (609.6mm) TENSION CYLINDER ROTATION +/- 90 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10°Forward to 90°Back, WRAPPING SPEED RANGE	 Adjustable, DIE LENGTH at full tonnage and 180° bend Minimum 20" (508 mm) Maximum 72" (1828.8 mm), DIE TABLE Pre drilled & threaded, Working Surface, 87" W x 49" D (2209.8 x 1244.6 mm), Height Table To Floor 35" (899 mm), MOTOR DRIVE Pump 25 H.P. 220/440 volts, EQUIPPED WITH 1- set 6” Jaws with Hydraulic Clamping, Serial Number 788
           CUSTOM STRETCH WRAP FORMER, STRETCH FORMING PRESS, FORMING TONNAGE 18, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 218" (5537.2 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), TENSION CYLINDER STROKE each 24”  (609.6mm) TENSION CYLINDER ROTATION +/- 90 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10°Forward to 90°Back, WRAPPING SPEED RANGE	 Adjustable, DIE LENGTH at full tonnage and 180° bend Minimum 20" (508 mm) Maximum 72" (1828.8 mm), DIE TABLE Pre drilled & threaded, Working Surface, 87" W x 49" D (2209.8 x 1244.6 mm), Height Table To Floor 35" (899 mm), MOTOR DRIVE Pump 25 H.P. 220/440 volts, EQUIPPED WITH 1- set 6” Jaws with Hydraulic Clamping, Serial Number 788, Photo Front
 Photo Front View.      CUSTOM STRETCH WRAP FORMER, STRETCH FORMING PRESS, FORMING TONNAGE 18, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 218" (5537.2 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), TENSION CYLINDER STROKE each 24”  (609.6mm) TENSION CYLINDER ROTATION +/- 90 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10°Forward to 90°Back, WRAPPING SPEED RANGE	 Adjustable, DIE LENGTH at full tonnage and 180° bend Minimum 20" (508 mm) Maximum 72" (1828.8 mm), DIE TABLE Pre drilled & threaded, Working Surface, 87" W x 49" D (2209.8 x 1244.6 mm), Height Table To Floor 35" (899 mm), MOTOR DRIVE Pump 25 H.P. 220/440 volts, EQUIPPED WITH 1- set 6” Jaws with Hydraulic Clamping, Serial Number 788, Photo Left Side  Photo Left Side.  
CUSTOM STRETCH WRAP FORMER, STRETCH FORMING PRESS, FORMING TONNAGE 18, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 218" (5537.2 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), TENSION CYLINDER STROKE each 24”  (609.6mm) TENSION CYLINDER ROTATION +/- 90 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10°Forward to 90°Back, WRAPPING SPEED RANGE	 Adjustable, DIE LENGTH at full tonnage and 180° bend Minimum 20" (508 mm) Maximum 72" (1828.8 mm), DIE TABLE Pre drilled & threaded, Working Surface, 87" W x 49" D (2209.8 x 1244.6 mm), Height Table To Floor 35" (899 mm), MOTOR DRIVE Pump 25 H.P. 220/440 volts, EQUIPPED WITH 1- set 6” Jaws with Hydraulic Clamping, Serial Number 788, Photo Close-up Pull Back Jaw Assembly.
 Photo Close-up Pull Back Jaw Assembly.       CUSTOM STRETCH WRAP FORMER, STRETCH FORMING PRESS, FORMING TONNAGE 18, DISTANCE BETWEEN JAWS Maximum Length of Part with Tension Cylinders fully retracted 218" (5537.2 mm), Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm), TENSION CYLINDER STROKE each 24”  (609.6mm) TENSION CYLINDER ROTATION +/- 90 Degrees, ARMS: SWING Simultaneous Arm Motion, Arm swings 10°Forward to 90°Back, WRAPPING SPEED RANGE	 Adjustable, DIE LENGTH at full tonnage and 180° bend Minimum 20" (508 mm) Maximum 72" (1828.8 mm), DIE TABLE Pre drilled & threaded, Working Surface, 87" W x 49" D (2209.8 x 1244.6 mm), Height Table To Floor 35" (899 mm), MOTOR DRIVE Pump 25 H.P. 220/440 volts, EQUIPPED WITH 1- set 6” Jaws with Hydraulic Clamping, Serial Number 788, Photo Close-up Controls  Photo Close-up Controls.


 

HUFFORD EXTRUSION and SHEET STRETCH WRAP FORMING MACHINE
Model A-12
TENSION CYLINDER PULL 60 tons
Distance between Gripper Jaws Clamp: 
with Tension Cylinders fully retracted Maximum 260" (6604 mm)
with Tension Cylinders fully extended Minimum    28" (711.20 mm)
TENSION CYLINDER ASSEMBLY
Tension Cylinder Stroke 30" (762 mm)
Tension Cylinder Swing +/- 25°

ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back.
DIE TABLE 50" FB  x 72" LR  (1270 mm x 1828 mm)
EQUIPPED WITH:
20" wide Gripper Jaws with hydraulic clamping.
8" wide Gripper Jaws with hydraulic clamping

Main Operator Station with Manual Controls

                           
Inventory Reference
S8120-10342  HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping
HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping, Photo Over-all left side to front Photo Left Side to Front over-all.     HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping, Photo left side to front Photo Left Side to Front.

HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping, Photo Front to Right Side. Photo Front to Right Side.     HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping, Photo Rear at Left Side to Front Photo Rear at Left Side to Front.    HUFFORD A12 EXTRUSION & SHEET STRETCH WRAP FORMING MACHINE, 60 tons FORMING TONNAGE, Distance between Jaws 260", 6604 mm maximum, 28", 711.20mm minimum, each Tension Cylinder Stroke 30", 762 mm, Tension Cylinder Swing +/- 25 Degrees, each arm swing Independent 10 Degrees Forward to 90 Degrees Back, Die Length at full tonnage and 180 degrees Wrap Minimum 20" (508 mm) Maximum	 72" (1829 mm), EQUIPPED WITH 1- set 20" wide Gripper Jaws with Hydraulic Clamping, Photo Operator Control Station Photo Operator Control Station.



The following Sheet Stretch Formers
TABLES are PARALLEL to FLOOR
                                                                                                           


1500 Ton CYRIL BATH CNC SHEET STRETCH FORMER
   Model  TCL-1500-100L-40 CNC       Date Mfg 1985
CURVED and STRAIGHT JAWS 95 inch wide
     Distance between Jaws 480 inch Maximum
    Jaws Swing Up thru 45 degrees,
DIE TABLE:
    Tilt Forward and Back
    Strokes Up 6 feet
Inventory Reference S8160-10287
Full specification will be posted by April 2015




The following Stretch Formers
TABLE ARE IN THE VERTICAL PLANE
                                                                                                              


HUFFORD  VERTICAL
SHEET STRETCH WRAP FORMER
Model A46
Die table is in Vertical Plane
Tension Cylinders  Pull 150 tons
JAWS: Width of 10 Segment Jaws 76”.
     10-Jaws that create a Curved & 1-Jaw Centroid (in center).
     Jaws Swing Right or Left.  Articulate and Adjust from Flat to Concave.
           Swing motion of tension cylinder on pivot pins 15 degrees inward & 30 degrees outward.
     Jaw  Assembly Rotates 20 degrees each side of vertical.
    Jaw Oscillation 15 degrees each side of centerline in planes of sheet.
DIE HEIGHT 72" Maximum.
DIE DEPTH 42" Maximum.
DIE LENGTH for 180 degree bend at full length 190" maximum.
           Minimum 40"
SHEET CAPACITY 66" X 144"

OPERATOR CONTROL STATION:
Inventory Reference
S8120-10027  HUFFORD SHEET and EXTRUSION STRETCH WRAP FORMER PRESS, model 46, CAPABILITIES sheet stretcher leveling -stretch wrap forming, SHEET CAPACITY 66”  width x 144” length, 10-JAWS - jaws rotate - swing left or right - articulate, adjust from flat to concave - oscillation, number of segment 10 x length of jaws 76”, 10 jaws that create a curved and 1-centroid jaw located in center, jaw oscillation cylinder 10” stroke - oscillates jaw assembly 10 degrees each side of centerline in planes of sheet, jaw assembly rotates from vertical, capacity of each carriage jaw 150 ton, DIE HEIGHT maximum 72”, DIE DEPTH maximum 42”, DIE LENGTH for 180 degree bend at full length 190”, minimum 40”, DIE TABLE 24” width x 72” height, 5-DIE BLOCKS POSITIONS 12” on centers, OPERATOR CONTROL STATION pump start / stop buttons, left hand and right hand jaw gripper cylinders, left hand and right hand tension cylinders, left hand and right hand jaw cylinders, left hand and right hand jaw rotation and oscillation cylinders, straightening cylinder, jaw curing cylinders, pressure gauges, motor drives are wired 440 volts, hydraulic system - separate systems, 2- arm actuating cylinders circuits each with separate power plants and piping but identical, 1- tension cylinder circuit operating both pairs of cylinders but with separate controls for each pair of cylinders, 1- jaw operating circuit with separate controls for each jaw and an oscillation - rotation and swing circuit with individual controls for each, 1- die positioning cylinder circuit is on the same circuit as the left-hand arm actuating cylinder, tension - rotation-oscillation and jaw cylinder hydraulic pumps each 60 HP 220/440 volts, arm actuating cylinder pumps each is driven by 15 HP 220/440 volts, gripper jaws cylinder pump 3 HP 220/440 volts, equipped with operator control station, Serial Number 10     HUFFORD SHEET and EXTRUSION STRETCH WRAP FORMER PRESS, model 46, CAPABILITIES sheet stretcher leveling -stretch wrap forming, SHEET CAPACITY 66”  width x 144” length, 10-JAWS - jaws rotate - swing left or right - articulate, adjust from flat to concave - oscillation, number of segment 10 x length of jaws 76”, 10 jaws that create a curved and 1-centroid jaw located in center, jaw oscillation cylinder 10” stroke - oscillates jaw assembly 10 degrees each side of centerline in planes of sheet, jaw assembly rotates from vertical, capacity of each carriage jaw 150 ton, DIE HEIGHT maximum 72”, DIE DEPTH maximum 42”, DIE LENGTH for 180 degree bend at full length 190”, minimum 40”, DIE TABLE 24” width x 72” height, 5-DIE BLOCKS POSITIONS 12” on centers, OPERATOR CONTROL STATION pump start / stop buttons, left hand and right hand jaw gripper cylinders, left hand and right hand tension cylinders, left hand and right hand jaw cylinders, left hand and right hand jaw rotation and oscillation cylinders, straightening cylinder, jaw curing cylinders, pressure gauges, motor drives are wired 440 volts, hydraulic system - separate systems, 2- arm actuating cylinders circuits each with separate power plants and piping but identical, 1- tension cylinder circuit operating both pairs of cylinders but with separate controls for each pair of cylinders, 1- jaw operating circuit with separate controls for each jaw and an oscillation - rotation and swing circuit with individual controls for each, 1- die positioning cylinder circuit is on the same circuit as the left-hand arm actuating cylinder, tension - rotation-oscillation and jaw cylinder hydraulic pumps each 60 HP 220/440 volts, arm actuating cylinder pumps each is driven by 15 HP 220/440 volts, gripper jaws cylinder pump 3 HP 220/440 volts, equipped with operator control station, Serial Number 10, photo taken prior to removal  This photo taken prior to removal.



600 Ton SHERIDAN GRAY VERTICAL SHEET & Extrusion STRETCH WRAP FORMER
 
Model E-600-24
 
Die table is in Vertical Plane
 
Capabilities: Sheet Stretcher Leveling,  Stretch Wrap Forming, Drape Forming.
 JAWS: Width of 8 Segment Jaws 84”.
      7-Jaws that create a Curved & 1-Jaw Centroid (in center).
      Jaws Rotate. Jaws Swing Right or Left.  Articulate.
      Swing or Move Up +45 degrees and Adjust from Flat to Concave.
      Jaw Oscillation 15 degrees each side of centerline in planes of sheet.
      Capacity of each Carriage Jaw, 300 Ton = TOTAL OVER-ALL 600 Tons
 WORK CAPACITY:
     Stroke Length minimum 0" and 288" maximum
     Die Width for 180 degree bend at full length 192" maximum.
     Die Width for 180 degree bend at full length 81" minimum      
 DIE TABLE
     Maximum Thickness - Sheet (with die backup adapter 76"
     Minimum Thickness 1"
     Maximum Width 192"
     Minimum Width 56"
     Maximum Depth 84"
 DIE TABLE Stroke 154"
 
ARM ACTUATING CYLINDERS: (two) Stroke each 76” 
 EQUIPPED WITH:
      Die Tables
      Operator Control Station.
 Inventory Reference S8160-10029
sheridan gray sheet and extrusion stretch wrap forming machine with Die Table in Vertical Plane and each arm has 8-segmented jaws which rotate,  swing left or right, articulate and adjust from flat to concave and has oscillation, number of segment 8_length of jaws 84”, with 7 jaws that create a curved and 1-centroid jaw located in center, option with100 jaws width, jaw oscillation cylinder and oscillates jaw assembly 10 degrees each side of centerline in planes of sheet, jaw assembly rotates from vertical, capacity of each carriage jaw is 300 tons for a total of 600 tons, Work Capacity minimum stock length is 0” and  maximum stock length is 288”, Minimum die width for 180º bend is 81” and  maximum die width for 180º bend is 192”, Die Table Capacity maximum thickness sheet with die backup adapter is 76”, minimum thickness 1”, maximum width 192”, minimum width 56”, maximum depth 84”, Die Table Cylinder stroke is 154” with a maximum thrust @ 3000 psi.is1, 240,000 lbs, Die Hold Down Cylinder two each stroke is 18”, Tension Cylinder two stroke each is 60”  with maximum pull @ 3000 psi is 642,000 lbs, Arm Actuating Cylinders two each stroke is 76”, Operator Control Station with pumps start - stop buttons - left hand and right hand jaw gripper cylinders - left hand and right hand tension cylinders - left hand and right hand jaw cylinders_left hand and right hand jaw rotation and oscillation cylinders, straightening cylinder, jaw curing cylinders, pressure gauges, Motor drives are wired 460 volts, two hydraulic pumps each 150 HP, one 25 HP, Capabilities CAPABILITIES ARE Sheet stretcher leveling - stretch wrap forming - drape forming
sheridan gray sheet and extrusion stretch wrap forming machine with Die Table in Vertical Plane and each arm has 8-segmented jaws which rotate,  swing left or right, articulate and adjust from flat to concave and has oscillation, number of segment 8_length of jaws 84”, with 7 jaws that create a curved and 1-centroid jaw located in center, option with100 jaws width, jaw oscillation cylinder and oscillates jaw assembly 10 degrees each side of centerline in planes of sheet, jaw assembly rotates from vertical, capacity of each carriage jaw is 300 tons for a total of 600 tons, Work Capacity minimum stock length is 0” and  maximum stock length is 288”, Minimum die width for 180º bend is 81” and  maximum die width for 180º bend is 192”, Die Table Capacity maximum thickness sheet with die backup adapter is 76”, minimum thickness 1”, maximum width 192”, minimum width 56”, maximum depth 84”, Die Table Cylinder stroke is 154” with a maximum thrust @ 3000 psi.is1, 240,000 lbs, Die Hold Down Cylinder two each stroke is 18”, Tension Cylinder two stroke each is 60”  with maximum pull @ 3000 psi is 642,000 lbs, Arm Actuating Cylinders two each stroke is 76”, Operator Control Station with pumps start - stop buttons - left hand and right hand jaw gripper cylinders - left hand and right hand tension cylinders - left hand and right hand jaw cylinders_left hand and right hand jaw rotation and oscillation cylinders, straightening cylinder, jaw curing cylinders, pressure gauges, Motor drives are wired 460 volts, two hydraulic pumps each 150 HP, one 25 HP, Capabilities CAPABILITIES ARE Sheet stretcher leveling - stretch wrap forming - drape forming   This photo taken of another unit, Please use as example.
 

This press is designed to produce formed sheet metal parts typically produced on drop hammer.
▼                                    ▼                                 ▼                                        ▼

SHERIDAN GRAY SHEET STRETCH DRAW FORMING PRESS
 Model SDP 250-120-60-1500

HYDRAULIC COMPRESSION PRESS: 250 Tons,   Down Acting 24½" stroke
Open Height 76"
Bed and Ram T-Slotted
Area with-in 4-Post 114" F-B x 130" L-R
Sheet Capacity 60" x 120"

two STRETCH JAWS:
  Width 64",  Stretch Tonnage 150, 
Jaw Oscillation Angle 10 degrees left / right.     Jaws Swing Up thru 22 degrees.     Jaw Tilt either side of center 15º.
Jaw Pull Down Cylinder Stroke Up thru11",    Tension Cylinder 54" stroke

OPERATOR CONTROL: Windows 2000 Software with Drop Down menus, tabs used to select the various
screens & controls buttons for input field and Manual Control Buttons.

Inventory Reference S8120-10043
sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus
sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus_Left Side-Front Photo Left Side-Front view.        sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus_Left Side-Rear view  Photo Left Side-Rear view        sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus_Rear view thru press and view with Electric control boxes and access ladder to hydraulic drive motors at top of press Photo Rear view       
 
sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus_Right Side to Front view Photo Right Side to Front view.          sheridan gray sheet stretch draw forming press_model SDP-250-120-60-150_Hydraulic Press Compression: 250 Tons_24 inch down acting stroke_open height 76 inch_T-slotted bed and ram_distance between 4-posts 114 inch foward back x 130 inch left right_stretch press 60 inch wide jaws x 120 inch sheet length_jaws swing up-tilt 15 degrees_swing left right 22 degrees_jaw rise fall thru 12 inch_pull back cylinders 24.5 inches_tension cylinders 54 inch stroke_controls software Window 2000 drop down menus_Operator Control Station Photo Operator Control Station.

 

DO YOU KNOW?
▼                     ▼
STRETCHER LEVELING: using Right Hand Jaw Only. The Flattening, Straightening or
     Leveling of material by stretching. Die Table not normally used during this forming mode.
STRETCHER LEVELING: Using both Right Hand and Left Hand Jaws --- Forming gradual
     Contoured Parts where die table movement is not required and the material is light enough to
     be bent and inserted in the jaws.
 
DRAPE FORMING: Drape Forming refers to forming of parts utilizing only the die table    
     stroke of the press. To Drape Form parts, the sheets are either sufficiently flexible to allow
     operator to bend the sheets over and around the form die to load the  parts into the jaws or
     the part may be preformed.  In this forming mode the jaws and tension cylinders are normally
     pre-positioned and locked for duration of cycle.
 
WRAP FORMING: Also called Stretch-Wrap Forming.  The forming of a part by first
     stretching the material and then causing the material to be wrapped around the die by
     combination of forcing the die into the material and manipulating the carriages to wrap
     parts under and around die.





* We will send full quotation and photo's, PLEASE CONTACT US *

Phone 213-627-2847     Fax 213-627-2499 or
E-Mail us at
sales@centurymachinery.com
 

 

SWAGING MACHINE S8650-

TORRINGTON ROTARY SWAGING MACHINE    Model 4
     Two DIE,

CAPACITY DIAMETER:  SOLID Mild Steel ⅝" (15.9mm)
                                    
TUBING 2" (50.8mm)
DIE WIDTH 1-15/16" 
(49.22mm)
DIE LENGTH 3"  (76.2mm)
DIE HEIGHT 2-11/16 " (68.26mm)
BACKER SIZE:
     Die Length   3" (76.2mm)
     Die Width     2" (50.8mm)
     Die Height    2-11/16" (68.26mm)
PART FEEDER:  Hand Feeder assembly is mounted onto preset rack.
       Feeder hand wheel moves tooling head

MOTOR DRIVE:  5 hp
EQUIPPED WITH:
     4-miscellaneous Die sets
    6- miscellaneous Liners sets.
    1- Spare Roller Rack Assembly 14" (355.6mm) outside diameter, 8" (203.2mm)
               inside diameter x 5" (127mm)  Ht.
    20- Rolls 2" (50.8mm) diameter x 3
" (85.73mm) length (8-new 12- very little use)
Inventory Reference S8650-10408
2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506
2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo Front to Left Side view Photo Front to Left Side view.      2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo Left Side view Photo Left Side view.     2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo Rear to Left Side view Photo Rear to Left Side view.

            2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo Rear at Right Side view Photo Rear at Right Side view.     2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo Front at Right Side view Photo Front at Right Side view.
2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo close-up Tooling Photo Close-up Tooling.        2" TORRINGTON DIE CLOSING SWAGING MACHINE, Model 4,TUBING with standard dies  2" 50.8mm, SOLID Mild Steel  ⅝" 15.9mm, DIAMETER HOLE thru SPINDLE 2" 50.8mm, LONGEST TAPER POSSIBLE 2¾"  69.85mm, Die Length 3", Die Width 1-15/16", Die Height  2-11/16", MOTOR 5 hp., PART FEEDER:  Hand Feeder assembly is mounted onto preset rack, EQUIPPED WITH 4-miscellaneous Die sets, 6- miscellaneous Liners sets, 1- Spare Roller Rack Assembly 14" outside diameter 8" inside diameter x 5" Ht, 20- Rolls 2" diameter x 3⅜" length, 8-new 12- very little use, Serial Number 4506, Photo close-up Spare Roller Assembly Photo Close-up Spare Roller Assembly.





 

 

We have the following:
AIRCRAFT GROUND SUPPORT EQUIPMENT

We have over 500 items in the above category

Air Conditioners Stand By  -  Airplane Portable Staircases  -    Air Start Units  -   Baggage Tractors.
D.C. Power Supply
  -  Generators AC Diesel Driven (Stand-By)  -   Generators 400 Cycle
Ground Power Units  -   Maintenance Stands  -   Push Back Tractors   -  Tow Tractors  -   Tugs  -
Wing Jacks
 

UNITED AIRCRAFT TOW TRACTOR                    Model SM160
DRAW BAR PULL 16,000 lbs

8  Cylinders Gasoline Powered ,   Power Steering
Length 11'3"  Width 7'8"  Height 57"           
Inventory Reference  M0798-9219
UNITED AIRCRAFT TOW TRACTOR  Model SM160 draw bar pull 16000 lbs  
Photo Right Side View                                Photo Right to Front View   UNITED AIRCRAFT TOW TRACTOR  Model SM160 draw bar pull 16000 lbs




 

** FOR YOUR: MILLING/ROUTING, SHAPING and
PROFILING NEEDS   
PLEASE GO TO

the following headings

ROUTERS or CNC VERTICAL PROFILERS (under Mills Vertical)
    

* We will send full quotation and photo's, PLEASE CONTACT US *
Phone 213-627-2847        Fax 213-627-2499 or
E-Mail us at  
sales@centurymachinery.com

" THANK YOU FOR TAKING THE TIME TO VISIT OUR SITE "