Link back to Home Page► www.centurymachinery.com
POINT and CLICK CATEGORIES or JUST SCROLL DOWN, PRESSES & PUNCHES CATEGORIES ARE IN ALPHABETICAL ORDER. ▬▬►
*H-FRAME Hydraulic Presses*
*KICK PRESSES*
*MOLDING PRESSES Four Posts * and a DOUBLE ACTING HYDRAULIC PRESS that makes its own forming dies
*PELLET PRESS*
*PUNCH PRESS ACCESSORIES: Air Feeds, Straighteners & Coil Reels*
*PUNCH, NIBBLER SHEAR & DUPLICATING *
*PUNCH PRESSES, OBI & GAP FRAME (All Types)*
*PUNCH SINGLE END, Hydraulic Power*
*PUNCHES Fabrication - Single End
Please use the Scroll Bar..................................................................>>>>>>>>>>
*PUNCHES TURRET*
*STRAIGHTENING PRESSES, Hydraulic*
*STRETCH WRAP FORMING MACHINES, Sheet & Plate, Mfg'd by Cyril Bath & Hufford* STRETCH FORMERS
*WHEEL PRESS: Hydraulic*
Serving Industry for 84 years
If you require a Quote Sheet PLEASE send us your requirements:
1937 South Santa Fe Avenue
Los Angeles, California 90021
Email sales@centurymachinery.com
Website www.centurymachinery.com
Telephone 1-213-627-2847
Fax 1-213-627-2499
MOLDING PRESSES, Hydraulic P5910-
and a
DOUBLE ACTING HYDRAULIC PRESS that MAKES ITS OWN FORMING DIES
THIS PRESS JUST SOLD
PHI MOLDING PRESS, Up Acting, 4-Post
Model IHIS75R-2536-4-81-C
Capacity 75 Tons
Ram Stroke 8"
Bed Size19" F-B x 28Ό" L-R
Electric Heated Top and Bottom
Platens Size 18½" x 18½" x 2½" Thick each
Open height with-out platens 19" Adjustable
Equipped with: Digital Controls.
2- Honeywell Temperature Gauges
Inventory Reference P5904-19018
Photo
H-FRAME PRESSES P5102- P5298-
NUGIER H-FRAME Hydraulic SHOP PRESS Model H60
Capacity 60 Tons
Ram Vertical Travel 8" by Hand Pump and Motorized to the hydraulic pump.
Ram Cylinder Head moves Right /Left
Ram diameter 2Ύ"
Distance between uprights 37"
Height under ram up, bed down bed 39"
Two Speed Ram
Equipped with: 1/3 hp Hydraulic Pump
Bed adjustment by hand crank
Inventory Reference P5102-10337
Photo left side to front.
Photo close-up hydraulic pump.
Photo close-up motor drive to hydraulic pump.
KICK PRESSES
PELLET PRESS P0875-
PUNCH, NIBBLER SHEAR & DUPLICATING
PUNCH PRESSES: OBI and Gap Frame
Flywheel and Back Geared
BLISS OBI PUNCH PRESS Model 21½
Flywheel Type, Single Crank
Capacity 50 Tons
Stroke 3"
Shut Height 13"
Slide Adjustment 2½"
Air Clutch and Air Brake
Motor Drive 5 hp.
Equipped with: Dual Electric Trip Buttons. and Electric Foot Trip
Inventory Reference P6209-9510
Photo
Photo
PUNCH PRESS ACCESSORIES: Feeders, Straighteners & Coil Reels
COILREEL Uncoiler
▼▼
LITTELL DOUBLE END COIL REEL
Model 5, Cast Number 5RS11C
SPECIFICATIONS
Coil Capacity 600 LBS.
Coil Width, Maximum 12"
Coil Outside Diameter, Maximum 46"
Range of Coil Inside Diameter 10" thru 20"
DISTANCE FLOOR TO CENTER OF COIL 36½"
REEL rotate 360 degrees
EQUIPPED WITH:
Self Centering. Four Arm Style Mandrels. Four Keepers.
Inventory Reference R1903-10054
Photo
COMBINATION FEEDER AND STRAIGHTENER
▼ ▼ ▼ ▼
COIL-MATIC AIR STOCK FEEDER and STRAIGHTENER
Model XHF-3012
SPECIFICATIONS AIR FEEDER
Stock Width 30"Maximum
Stroke Range 0 thru 12"
Stock Thickness 0.061"
Stroke Cycles per minute at maximum stroke 45
Pneumatic Driven Stock Gripper
SPECIFICATIONS STRAIGHTENING PINCH ROLLS
Five Rolls (2 over 3) each roll diameter 2"
EQUIPPED WITH:
Stroke Length Adjustable via hand crank.
Manual Top Straightening Roll adjustment.
Stock Edge Guide.
Infeed Skate Conveyor 24" x 24"
Mounted on Portable Frame with Height Adjustment.
Inlet
COIL MATIC SINGLE END POWER UNCOILER REEL
Model PR3-3054-A
SPECIFICATIONS
Coil Capacity 6000 LBS.
Coil Width, Maximum 30"
Coil Outside Diameter, Maximum 54"
Range of Coil Inside Diameter10" thru 20"
Infinitely Variable 5 thru 150 FPM
VARI DRIVE: Motor 2 hp
EQUIPPED WITH:
Self Centering. Three Arm Style Mandrels.
Three Keepers.
Inventory Reference R1903-10256 Photo right side view with controls.
Photo End view Arms.
Photo End to Right Side view Arms and Keepers.
Photo close-up ID Tag
Please Note you may wish to purchase the Coil-Matic Air Feeder & Straightener to go with this unit.
Air Filter and Oiler.
Inventory Reference S7748-10257
Photo end view Gripper- Conveyor and portable stand with height adjustment.
Photo close-up Gripper- Conveyor and portable stand with height adjustment.
Photo close-up side view Gripper Stroke cylinder and adjustment control.
Photo End view with Straightener, Stroke Control and Height adjustment control.
Please Note you may wish to purchase the Coil-Matic 6000 lbs Uncoiler to go with this unit.
ROWE STOCK STRAIGHTENER AND FEEDER Model S-15M
CAPACITY STRAIGHTENER
Width 15" x Thickness,
Maximum Mild Steel 0.30" thru 0.125"
ROLLS SPEED, Variable 35 thru 100 fpm,
MOTOR DRIVE 2 H.P.
Controls Model MBRM-215.
Inventory Reference S7748-9485
Photo Operator Controls Side view.
Photo Infeed to Operator Control side.
Photo Operator Control Side view to Out-Feed End. End
Photo Right End to Controls Cabinet at rear.
COMBINATION FEEDER AND STRAIGHTENER
HEBBLE Rack "N" Roll, PUNCH PRESS FEEDER Capacity 2½" wide
connected to COOPER WEYMOUTH STOCK STRAIGHTENER 7 Rolls
Inventory Reference F0854-4033
PUNCHES Fabrication - Single End P8959-
PUNCH SINGLE END, Hydraulic Power
P9135- CNC P9150- Non CNC
PORTABLE HOLE PUNCHES
PUNCH HOLES IN: Flange - Web - Beam - Channel - Angle -Flat
PUNCHES TURRET P9275-
ROTEX TURRET PUNCH Model 18BK-60
Capacity 8 -Tons
18-Stations
24" Throat
Capacity 5/32" diameter thru 2"
Equipped with
(17) Punch & Die Sets 5/32" thru 2" Diameter.
(1) 2" wide Nibbler Shear
Sheet Table 36" FB x 54"
Mounted on stand.
Inventory Reference P9275-10439
Photo Front to Right Side.
Photo Turret Positions A thru I.
Photo Turret Positions G thru M.
Photo Turret Positions L thru P.
Photo Turret Positions M thru Q.
Photo Turret Positions O thru Nibbler Shear.
Photo close-up Nibbler Shear.
ROTEX TURRET PUNCH Model 18CH-2.25
Hydraulic Driven
Capacity 15-Tons
18-Stations
26" Throat
Equipped with
(18) Punch & Die Sets 5/16" thru 2Ό" Diameter.
Hydraulic Pump motor drive 5 HP
Table Working Surface, 48" x 48"
(1) Guide Fence
Inventory Reference P9275-10184
New replacement cost $42,533.00 Photo Front to left side.
Photo Right side to front view.
Photo Down view at Left side.
Photo Punch & Dies with-in Turret.
Photo Punch & Dies with-in Turret.
STRAIGHTENING PRESSES P5298-
Hydraulic Driven (ALL TYPES)
DENISON C-Frame STRAIGHTENING HYDRAULIC PRESS
Model SC2-50
Capacity 50 Tons
Stroke17"
Throat depth center line of ram 12"
Bed Size 20" x 60"
Inventory Reference P5298-8874
Photo show press as it exist, before removal of protective coating on Ram Photo
STRETCH WRAP FORMING MACHINES,
STRETCH FORMERS
Sheet & Plate, Mfg'd by: Cyril Bath and Hufford S8120-
THE FOLLOWING are EXTRUSION STRETCH WRAP FORMERS:
▼ ▼ ▼ ▼ ▼
NAS PLANT HORIZONTAL Extrusion STRETCH WRAP FORMING PRESS
FORMING TONNAGE 11
DISTANCE BETWEEN JAWS:
Maximum Length of Part with Tension Cylinders
fully retracted 136" (3,454.4 mm)
Minimum Length of Part with Tension Cylinders fully extended 10" (254 mm)
TENSION CYLINDER STROKE each with 3" long spacer to reduce stroke to 7" (177.6mm)
TENSION CYLINDER ROTATION +/- 25 Degrees
ARMS: SWING Simultaneous Arm Motion Arm swings 10° Forward to 90°Back.
DIE TABLE: Working Surface 35⅝" width x 35Ύ" depth (908.88 x 908.05 mm)
Hydraulic Pump 10 hp.
EQUIPPED WITH:
1-set 3" Jaws with Pneumatic Clamping
17-Miscellaneous set of Gripper Jaws
7- single Gripper Jaws
Inventory Reference S8120-10423
Photo Front view.
Photo Left side to Front.
Photo extra Gripper Jaws.
L&F HUFFORD HORIZONTAL CNC Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A-5
FORMING TONNAGE 12
DISTANCE BETWEEN JAWS 115" (2,921 mm)
ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back.
DIE LENGTH at FULL TONNAGE and 180 degrees Wrap:
Minimum 11" (279.4 mm) Maximum 40" (1,016 mm)
DIE TABLE: 48 Pre drilled & threaded
Working Surface 42" W x 44Ύ" D (1,066.8 mm X 1,136.65 mm)
HYDRAULIC PUMP MOTOR DRIVE: 30 H.P.
CONTROLS: DeMott CNC Controls with: Programmable Key Pad, CRT and Hand Function Buttons.
REMOTE HAND CONTROLS located on each arm with 2-Tension Cylinder In/Out push buttons,
Tension Cylinder Load and Stop Push Buttons. Jaw Close / Open Switch. Carriage In / Out Switch.
EQUIPPED WITH:
1-set of 4" Jaws with Hydraulic Clamping. 1-set Adjustable Die Post.
Farval Centralized Lubrication System SS-4200. Thermal Transfer Products Heat Exchanger.
Inventory Ref: S8120-10259 Photo Left Side over-all view.
Photo Front to Left Side view.
Photo Down view Table, Jaws, and Adjustable Die Post.
Photo rear view Electrical Control Cabinet, Hydraulic Power Pack.
Photo side view Hydraulic Power Pack.
CYRIL BATH CNC HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model V-10 QUAD AXIS
CNC Controls
Tension Cylinders Pull 10 tons
Distance between Gripper Jaws Clamp: Maximum 113" (2,870.2mm)
Minimum 27" (685.8mm)
Arm SWING BACK 82 degrees
Tension Cylinder Stroke 43"
GRIPPER JAWS ROTATION 180 degrees
Swings Left/Right +/-25 degrees TILT +/-10 degrees
GRIPPER JAWS CARRIAGE with Rise and Fall
EQUIPPED WITH:
Operator CNC Controls and Manual Controls
Nova Gantry Die Changeover system with Rotary Table
Four Hydraulic Tool Clamps
Inventory Reference S8120-10232
Photos with-in taken in plant prior to Stretch Former being decommissioned.
Photo Front-Right Side, Quad Axis Jaw Carriage Assembly & Die Clamps.
Photo Front-Right Side.
Photo Operator Control Station Station.
Photo Close Up CRT & KEYBOARD.
Photo Close Up Operator Hand Controls.
Photo Close-up 4-Die Holders and Quad Jaw Holders & Manuals.
Photo Down View Die Table and Four Adjustable Hydraulic Die Clamps.
Photo Rear view Quad Axis Jaw Carriage and Hydraulic Pump.
Photo Trabon Auto Lube Maxi-Monitor Control Mark111, Lubriquip.
Photo Electrical Control Cabinet.
CYRIL BATH CNC HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model V-10 QUAD AXIS
CNC Controls
Distance between Gripper Jaws Clamp: Maximum 113" (2,870.2mm)
Minimum 27" (685.8mm)
Arm SWING BACK 82 degrees
Tension Cylinder Stroke 43"
GRIPPER JAWS ROTATION 180 degrees
Swings Left/Right +/-25 degrees TILT +/-10 degrees
GRIPPER JAWS CARRIAGE with Rise and Fall
EQUIPPED WITH:
Operator CNC Controls and Manual Controls
Nova Gantry Die Changeover system with Rotary Table
Four Hydraulic Tool Clamps
Inventory Reference S8120-10233
Photos with-in taken in plant prior to Stretch Former being decommissioned.
Photos with-in taken in plant prior to Stretch Former being decommissioned.
Photo Front view Work Area.
Photo Front to Right Side.
Photo Close-up Die Holders and Quad Jaw Holders.
Photo Down View Table and 4-Die Clamps.
Photo side view Jaw Holder and 4-Die Clamps.
Photo Control Counsel with CRT, Program Keyboard and Operation Hand Controls.
Photo Hydraulic Power Unit.
Photo rear view right side with Hydraulic Power Pack & Electric Power Knife Switch.
Photo Control Cabinet and Hydraulic Power Unit.
Photo Trabon Maxi Monitor Mark 111, Lubriquip.
Photo view looking up at Nova Gantry Die Changeover.
Photo Partial view of Nova Die Changeover motor drives.
Photo Nova Die Changeover Part Turn Table.
CYRIL BATH HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Tension Cylinders Pull 12½ tons
Distance between Jaws Clamp: Maximum 120"
with 6" Jaws
Inventory Reference S8120-10026
HUFFORD HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Model A10
Tension Cylinders Pull 17½ tons
Distance between Jaws Clamp: Maximum 219" (5562.6mm)
with 4" Jaws
Die length at full tonnage and 180 degree bend: Minimum 20" Maximum 68"
Inventory Reference S8120-10025
Photo Front Left Side View.
Photo Hydraulic Pump and Left Side View.
HUFFORD HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
ModelA10
Tension Cylinders Pull 17½ tons
Distance between Jaws Clamp: Maximum 205" (5207mm)
with 6" Jaws
Die length at full tonnage and 180 degree bend: Minimum 20" Maximum 68"
Inventory Reference S8120-10220
Photo Left Side to Front View.
Photo Front to Right Side.
Photo Close Up 6 inch Jaws.
CUSTOM HORIZONTAL Extrusion STRETCH WRAP FORMER (Stretch Forming Press)
Tension Cylinders Pull 19 tons
Distance between Jaws Clamp: Maximum 218 (5237.2mm)
with 4" Jaws
Die length at full tonnage and 180 degree bend: Minimum 20" Maximum 72"
Inventory Reference S8120-10218
Photo Front View.
Photo Left Side.
Photo Close-up Pull Back Jaw Assembly.
Photo Close-up Controls.
HUFFORD EXTRUSION and SHEET STRETCH WRAP FORMING MACHINE
Model A-12
TENSION CYLINDER PULL 60 tons
Distance between Gripper Jaws Clamp: with Tension Cylinders fully retracted Maximum 260" (6604 mm)
with Tension Cylinders fully extended Minimum 28" (711.20 mm)
TENSION CYLINDER ASSEMBLY
Tension Cylinder Stroke 30" (762 mm)
Tension Cylinder Swing +/- 25°
ARM SWING (each Arm has Independent Movement) 10° Forward to 90° Back.
DIE TABLE 50" FB x 72" LR (1270 mm x 1828 mm)
EQUIPPED WITH:
20" wide Gripper Jaws with hydraulic clamping.
6" diameter Gripper Jaws
Main Operator Station with Manual Controls
Inventory Reference S8120-10342 Photo Left Side to Front over-all.
Photo Left Side to Front.
Photo Front to Right Side.
Photo Rear at Left Side to Front.
Photo Operator Control Station.
THE FOLLOWING STRETCH FORMERS
(DIE TABLE are in a VERTICAL PLANE
▼ ▼
HUFFORD VERTICAL SHEET STRETCH WRAP FORMER
Model A46
Die table is in Vertical Plane
Tension Cylinders Pull 150 tons
JAWS: Width of 10 Segment Jaws 76.
10-Jaws that create a Curved & 1-Jaw Centroid (in center).
Jaws Swing Right or Left. Articulate and Adjust from Flat to Concave.
Swing motion of tension cylinder on pivot pins 15 degrees inward & 30 degrees outward.
Jaw Assembly Rotates 20 degrees each side of vertical.
Jaw Oscillation 15 degrees each side of centerline in planes of sheet.
DIE HEIGHT 72" Maximum.
DIE DEPTH 42" Maximum.
DIE LENGTH for 180 degree bend at full length 190" maximum.
Minimum 40"
SHEET CAPACITY 66" X 144"
OPERATOR CONTROL STATION:
Inventory Reference S8120-10027
This photo taken prior to removal.
600 Ton SHERIDAN GRAY VERTICAL SHEET & Extrusion STRETCH WRAP FORMER
Model E-600-24
Die table is in Vertical Plane
Capabilities: Sheet Stretcher Leveling, Stretch Wrap Forming, Drape Forming.
JAWS: Width of 8 Segment Jaws 84.
7-Jaws that create a Curved & 1-Jaw Centroid (in center).
Jaws Rotate. Jaws Swing Right or Left. Articulate.
Swing or Move Up +45 degrees and Adjust from Flat to Concave.
Jaw Oscillation 15 degrees each side of centerline in planes of sheet.
Capacity of each Carriage Jaw, 300 Ton = TOTAL OVER-ALL 600 Tons
WORK CAPACITY:
Stroke Length minimum 0" and 288" maximum.
Die Width for 180 degree bend at full length 192" maximum.
Die Width for 180 degree bend at full length 81" minimum.
DIE TABLE
Maximum Thickness - Sheet (with die backup adapter 76"
Minimum Thickness 1"
Maximum Width 192"
Minimum Width 56"
Maximum Depth 84"
DIE TABLE Stroke 154"
ARM ACTUATING CYLINDERS: (two) Stroke each 76
EQUIPPED WITH:
Die Tables
Operator Control Station.
Inventory Reference S8160-10029 This photo taken of another unit, Please use as example.
DO YOU KNOW ?
▼ ▼
STRETCHER LEVELING: using Right Hand Jaw Only. The Flattening, Straightening or
Leveling of material by stretching. Die Table not normally used during this forming mode.
STRETCHER LEVELING: Using both Right Hand and Left Hand Jaws --- Forming gradual
Contoured Parts where die table movement is not required and the material is light enough to
be bent and inserted in the jaws.
DRAPE FORMING: Drape Forming refers to forming of parts utilizing only the die table
stroke of the press. To Drape Form parts, the sheets are either sufficiently flexible to allow
operator to bend the sheets over and around the form die to load the parts into the jaws or
the part may be preformed. In this forming mode the jaws and tension cylinders are normally
pre-positioned and locked for duration of cycle.
WRAP FORMING: Also called Stretch-Wrap Forming. The forming of a part by first
stretching the material and then causing the material to be wrapped around the die by
combination of forcing the die into the material and manipulating the carriages to wrap
parts under and around die.
WE ARE LOOKING TO PURCHASE one machine or entire facility:
STRETCH WRAP FORMER (Stretch Forming Press)
WHEEL PRESS, Hydraulic P7898-
Sorry we are out of stock, but were are looking to buy one machine of entire Facility.
PLEASE CONTACT US FOR QUOTATION and PHOTO'S
Phone 1-213-627-2847, FAX 1-213-627-2499 or
E-Mail us at sales@centurymachinery.com
" THANK YOU for taking the time to visit our web site "